void momenco_time_init(void)
{
setup_wired_tlb_entries();
/*
* Ocelot-3 board has been built with both
* the Rm7900 and the Rm7065C
*/
mips_hpt_frequency = cpu_clock / 2;
rtc_mips_get_time = m48t37y_get_time;
rtc_mips_set_time = m48t37y_set_time;
}
void __init plat_setup(void)
{
unsigned int tmpword;
board_time_init = momenco_time_init;
_machine_restart = momenco_ocelot_restart;
_machine_halt = momenco_ocelot_halt;
pm_power_off = momenco_ocelot_power_off;
/* Wired TLB entries */
setup_wired_tlb_entries();
/* shut down ethernet ports, just to be sure our memory doesn't get
* corrupted by random ethernet traffic.
*/
MV_WRITE(MV64340_ETH_TRANSMIT_QUEUE_COMMAND_REG(0), 0xff << 8);
MV_WRITE(MV64340_ETH_TRANSMIT_QUEUE_COMMAND_REG(1), 0xff << 8);
MV_WRITE(MV64340_ETH_RECEIVE_QUEUE_COMMAND_REG(0), 0xff << 8);
MV_WRITE(MV64340_ETH_RECEIVE_QUEUE_COMMAND_REG(1), 0xff << 8);
do {}
while (MV_READ(MV64340_ETH_RECEIVE_QUEUE_COMMAND_REG(0)) & 0xff);
do {}
while (MV_READ(MV64340_ETH_RECEIVE_QUEUE_COMMAND_REG(1)) & 0xff);
do {}
while (MV_READ(MV64340_ETH_TRANSMIT_QUEUE_COMMAND_REG(0)) & 0xff);
do {}
while (MV_READ(MV64340_ETH_TRANSMIT_QUEUE_COMMAND_REG(1)) & 0xff);
MV_WRITE(MV64340_ETH_PORT_SERIAL_CONTROL_REG(0),
MV_READ(MV64340_ETH_PORT_SERIAL_CONTROL_REG(0)) & ~1);
MV_WRITE(MV64340_ETH_PORT_SERIAL_CONTROL_REG(1),
MV_READ(MV64340_ETH_PORT_SERIAL_CONTROL_REG(1)) & ~1);
/* Turn off the Bit-Error LED */
OCELOT_FPGA_WRITE(0x80, CLR);
tmpword = OCELOT_FPGA_READ(BOARDREV);
if (tmpword < 26)
printk("Momenco Ocelot-3: Board Assembly Rev. %c\n",
'A'+tmpword);
else
printk("Momenco Ocelot-3: Board Assembly Revision #0x%x\n",
tmpword);
tmpword = OCELOT_FPGA_READ(FPGA_REV);
printk("FPGA Rev: %d.%d\n", tmpword>>4, tmpword&15);
tmpword = OCELOT_FPGA_READ(RESET_STATUS);
printk("Reset reason: 0x%x\n", tmpword);
switch (tmpword) {
case 0x1:
printk(" - Power-up reset\n");
break;
case 0x2:
printk(" - Push-button reset\n");
break;
case 0x4:
printk(" - cPCI bus reset\n");
break;
case 0x8:
printk(" - Watchdog reset\n");
break;
case 0x10:
printk(" - Software reset\n");
break;
default:
printk(" - Unknown reset cause\n");
}
reset_reason = tmpword;
OCELOT_FPGA_WRITE(0xff, RESET_STATUS);
tmpword = OCELOT_FPGA_READ(CPCI_ID);
printk("cPCI ID register: 0x%02x\n", tmpword);
printk(" - Slot number: %d\n", tmpword & 0x1f);
printk(" - PCI bus present: %s\n", tmpword & 0x40 ? "yes" : "no");
printk(" - System Slot: %s\n", tmpword & 0x20 ? "yes" : "no");
tmpword = OCELOT_FPGA_READ(BOARD_STATUS);
printk("Board Status register: 0x%02x\n", tmpword);
printk(" - User jumper: %s\n", (tmpword & 0x80)?"installed":"absent");
printk(" - Boot flash write jumper: %s\n", (tmpword&0x40)?"installed":"absent");
printk(" - L3 cache size: %d MB\n", (1<<((tmpword&12) >> 2))&~1);
/* Support for 128 MB memory */
add_memory_region(0x0, 0x08000000, BOOT_MEM_RAM);
}