static void twl4030_phy_power(struct twl4030_usb *twl, int on)
{
u8 pwr;
pwr = twl4030_usb_read(twl, PHY_PWR_CTRL);
if (on) {
regulator_enable(twl->usb3v1);
regulator_enable(twl->usb1v8);
/*
* Disabling usb3v1 regulator (= writing 0 to VUSB3V1_DEV_GRP
* in twl4030) resets the VUSB_DEDICATED2 register. This reset
* enables VUSB3V1_SLEEP bit that remaps usb3v1 ACTIVE state to
* SLEEP. We work around this by clearing the bit after usv3v1
* is re-activated. This ensures that VUSB3V1 is really active.
*/
twl_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER, 0,
VUSB_DEDICATED2);
regulator_enable(twl->usb1v5);
pwr &= ~PHY_PWR_PHYPWD;
WARN_ON(twl4030_usb_write_verify(twl, PHY_PWR_CTRL, pwr) < 0);
twl4030_usb_write(twl, PHY_CLK_CTRL,
twl4030_usb_read(twl, PHY_CLK_CTRL) |
(PHY_CLK_CTRL_CLOCKGATING_EN |
PHY_CLK_CTRL_CLK32K_EN));
} else {
pwr |= PHY_PWR_PHYPWD;
WARN_ON(twl4030_usb_write_verify(twl, PHY_PWR_CTRL, pwr) < 0);
regulator_disable(twl->usb1v5);
regulator_disable(twl->usb1v8);
regulator_disable(twl->usb3v1);
}
}
static void twl4030_i2c_access(struct twl4030_usb *twl, int on)
{
unsigned long timeout;
int val = twl4030_usb_read(twl, PHY_CLK_CTRL);
if (val >= 0) {
if (on) {
/* enable DPLL to access PHY registers over I2C */
val |= REQ_PHY_DPLL_CLK;
WARN_ON(twl4030_usb_write_verify(twl, PHY_CLK_CTRL,
(u8)val) < 0);
timeout = jiffies + HZ;
while (!(twl4030_usb_read(twl, PHY_CLK_CTRL_STS) &
PHY_DPLL_CLK)
&& time_before(jiffies, timeout))
udelay(10);
if (!(twl4030_usb_read(twl, PHY_CLK_CTRL_STS) &
PHY_DPLL_CLK))
dev_err(twl->dev, "Timeout setting T2 HSUSB "
"PHY DPLL clock\n");
} else {
/* let ULPI control the DPLL clock */
val &= ~REQ_PHY_DPLL_CLK;
WARN_ON(twl4030_usb_write_verify(twl, PHY_CLK_CTRL,
(u8)val) < 0);
}
}
}
static void twl4030_phy_power(struct twl4030_usb *twl, int on)
{
u8 pwr;
pwr = twl4030_usb_read(PHY_PWR_CTRL);
if (on) {
pwr &= ~PHY_PWR_PHYPWD;
if (twl4030_usb_write_verify(PHY_PWR_CTRL, pwr) < 0) {
printk(KERN_ERR "twl4030_usb: i2c write failed,"
" line %d\n", __LINE__);
return;
}
twl4030_usb_write(PHY_CLK_CTRL,
twl4030_usb_read(PHY_CLK_CTRL) |
(PHY_CLK_CTRL_CLOCKGATING_EN |
PHY_CLK_CTRL_CLK32K_EN));
} else {
pwr |= PHY_PWR_PHYPWD;
if (twl4030_usb_write_verify(PHY_PWR_CTRL, pwr) < 0) {
printk(KERN_ERR "twl4030_usb: i2c write failed,"
" line %d\n", __LINE__);
}
}
return;
}
static void twl4030_phy_power(struct twl4030_usb *twl, int on)
{
u8 pwr;
pwr = twl4030_usb_read(twl, PHY_PWR_CTRL);
if (on) {
regulator_enable(twl->usb3v1);
regulator_enable(twl->usb1v8);
twl4030_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER, 0,
VUSB_DEDICATED2);
regulator_enable(twl->usb1v5);
pwr &= ~PHY_PWR_PHYPWD;
WARN_ON(twl4030_usb_write_verify(twl, PHY_PWR_CTRL, pwr) < 0);
twl4030_usb_write(twl, PHY_CLK_CTRL,
twl4030_usb_read(twl, PHY_CLK_CTRL) |
(PHY_CLK_CTRL_CLOCKGATING_EN |
PHY_CLK_CTRL_CLK32K_EN));
} else {
pwr |= PHY_PWR_PHYPWD;
WARN_ON(twl4030_usb_write_verify(twl, PHY_PWR_CTRL, pwr) < 0);
regulator_disable(twl->usb1v5);
regulator_disable(twl->usb1v8);
regulator_disable(twl->usb3v1);
}
}
static void twl4030_phy_power(struct twl4030_usb *twl, int on)
{
u8 pwr;
pwr = twl4030_usb_read(twl, PHY_PWR_CTRL);
printk(KERN_ERR "twl4030_phy_power + : PHY_PWR_CTRL=%x ====^^==== (twl4030-usb.c)\n", pwr);
pwr = twl4030_usb_read(twl, PHY_CLK_CTRL);
printk(KERN_ERR "twl4030_phy_power + : PHY_CLK_CTRL=%x ====^^==== (twl4030-usb.c)\n", pwr);
pwr = twl4030_usb_read(twl, PHY_CLK_CTRL_STS);
printk(KERN_ERR "twl4030_phy_power + : PHY_CLK_CTRL_STS=%x ====^^==== (twl4030-usb.c)\n", pwr);
if (on) {
#if 0 /* LGE_CHANGE [HEAVEN: [email protected]] on 2009-10-14, for <25.12 USB interrupt fix> */
regulator_enable(twl->usb3v1);
regulator_enable(twl->usb1v8);
#endif
/*
* Disabling usb3v1 regulator (= writing 0 to VUSB3V1_DEV_GRP
* in twl4030) resets the VUSB_DEDICATED2 register. This reset
* enables VUSB3V1_SLEEP bit that remaps usb3v1 ACTIVE state to
* SLEEP. We work around this by clearing the bit after usv3v1
* is re-activated. This ensures that VUSB3V1 is really active.
*/
twl_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER, 0,
VUSB_DEDICATED2);
#if 1 /* LGE_CHANGE [HEAVEN: [email protected]] on 2009-10-14, for <25.12 USB interrupt fix> */
regulator_enable(twl->usb1v8);
#endif
regulator_enable(twl->usb1v5);
pwr &= ~PHY_PWR_PHYPWD;
WARN_ON(twl4030_usb_write_verify(twl, PHY_PWR_CTRL, pwr) < 0);
twl4030_usb_write(twl, PHY_CLK_CTRL,
twl4030_usb_read(twl, PHY_CLK_CTRL) |
(PHY_CLK_CTRL_CLOCKGATING_EN |
PHY_CLK_CTRL_CLK32K_EN));
} else {
msleep(250); // LGE_CHANGE [HUB] jjun.lee for USB unplug detect (TI Girish)
pwr |= PHY_PWR_PHYPWD;
WARN_ON(twl4030_usb_write_verify(twl, PHY_PWR_CTRL, pwr) < 0);
regulator_disable(twl->usb1v5);
regulator_disable(twl->usb1v8);
#if 1 /* LGE_CHANGE [HEAVEN: [email protected]] on 2009-10-14, for <25.12 USB interrupt fix> */
/* Put VUSB3V1 regulator in sleep mode */
twl_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER, 0x08,
VUSB_DEDICATED2);
#else
regulator_disable(twl->usb3v1);
#endif
}
pwr = twl4030_usb_read(twl, PHY_PWR_CTRL);
printk(KERN_ERR "twl4030_phy_power - : PHY_PWR_CTRL=%x ====^^==== (twl4030-usb.c)\n", pwr);
pwr = twl4030_usb_read(twl, PHY_CLK_CTRL);
printk(KERN_ERR "twl4030_phy_power - : PHY_CLK_CTRL=%x ====^^==== (twl4030-usb.c)\n", pwr);
pwr = twl4030_usb_read(twl, PHY_CLK_CTRL_STS);
printk(KERN_ERR "twl4030_phy_power - : PHY_CLK_CTRL_STS=%x ====^^==== (twl4030-usb.c)\n", pwr);
}
static void twl4030_phy_power(struct twl4030_usb *twl, int on)
{
u8 pwr;
pwr = twl4030_usb_read(twl, PHY_PWR_CTRL);
if (on) {
pwr &= ~PHY_PWR_PHYPWD;
WARN_ON(twl4030_usb_write_verify(twl, PHY_PWR_CTRL, pwr) < 0);
twl4030_usb_write(twl, PHY_CLK_CTRL,
twl4030_usb_read(twl, PHY_CLK_CTRL) |
(PHY_CLK_CTRL_CLOCKGATING_EN |
PHY_CLK_CTRL_CLK32K_EN));
} else {
pwr |= PHY_PWR_PHYPWD;
WARN_ON(twl4030_usb_write_verify(twl, PHY_PWR_CTRL, pwr) < 0);
}
}
static void __twl4030_phy_power(struct twl4030_usb *twl, int on)
{
u8 pwr = twl4030_usb_read(twl, PHY_PWR_CTRL);
if (on)
pwr &= ~PHY_PWR_PHYPWD;
else
pwr |= PHY_PWR_PHYPWD;
WARN_ON(twl4030_usb_write_verify(twl, PHY_PWR_CTRL, pwr) < 0);
}
static void twl4030_i2c_access(int on)
{
unsigned long timeout;
int val = twl4030_usb_read(PHY_CLK_CTRL);
if (val >= 0) {
if (on) {
/* enable DPLL to access PHY registers over I2C */
val |= REQ_PHY_DPLL_CLK;
if (twl4030_usb_write_verify(PHY_CLK_CTRL,
(u8)val) < 0) {
printk(KERN_ERR "twl4030_usb: i2c write failed,"
" line %d\n", __LINE__);
return;
}
timeout = jiffies + HZ;
while (!(twl4030_usb_read(PHY_CLK_CTRL_STS) &
PHY_DPLL_CLK)
&& time_before(jiffies, timeout))
udelay(10);
if (!(twl4030_usb_read(PHY_CLK_CTRL_STS) &
PHY_DPLL_CLK))
printk(KERN_ERR "Timeout setting T2 HSUSB "
"PHY DPLL clock\n");
} else {
/* let ULPI control the DPLL clock */
val &= ~REQ_PHY_DPLL_CLK;
if (twl4030_usb_write_verify(PHY_CLK_CTRL,
(u8)val) < 0) {
printk(KERN_ERR "twl4030_usb: i2c write failed,"
" line %d\n", __LINE__);
}
}
}
return;
}