static void at91sam9260ek_macb_hw_init(void)
{
struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
struct at91_port *pioa = (struct at91_port *)ATMEL_BASE_PIOA;
struct at91_rstc *rstc = (struct at91_rstc *)ATMEL_BASE_RSTC;
unsigned long erstl;
/* Enable EMAC clock */
writel(1 << ATMEL_ID_EMAC0, &pmc->pcer);
/*
* Disable pull-up on:
* RXDV (PA17) => PHY normal mode (not Test mode)
* ERX0 (PA14) => PHY ADDR0
* ERX1 (PA15) => PHY ADDR1
* ERX2 (PA25) => PHY ADDR2
* ERX3 (PA26) => PHY ADDR3
* ECRS (PA28) => PHY ADDR4 => PHYADDR = 0x0
*
* PHY has internal pull-down
*/
writel(pin_to_mask(AT91_PIN_PA14) |
pin_to_mask(AT91_PIN_PA15) |
pin_to_mask(AT91_PIN_PA17) |
pin_to_mask(AT91_PIN_PA25) |
pin_to_mask(AT91_PIN_PA26) |
pin_to_mask(AT91_PIN_PA28),
&pioa->pudr);
erstl = readl(&rstc->mr) & AT91_RSTC_MR_ERSTL_MASK;
/* Need to reset PHY -> 500ms reset */
writel(AT91_RSTC_KEY | AT91_RSTC_MR_ERSTL(13) |
AT91_RSTC_MR_URSTEN, &rstc->mr);
writel(AT91_RSTC_KEY | AT91_RSTC_CR_EXTRST, &rstc->cr);
/* Wait for end hardware reset */
while (!(readl(&rstc->sr) & AT91_RSTC_SR_NRSTL))
;
/* Restore NRST value */
writel(AT91_RSTC_KEY | erstl | AT91_RSTC_MR_URSTEN,
&rstc->mr);
/* Re-enable pull-up */
writel(pin_to_mask(AT91_PIN_PA14) |
pin_to_mask(AT91_PIN_PA15) |
pin_to_mask(AT91_PIN_PA17) |
pin_to_mask(AT91_PIN_PA25) |
pin_to_mask(AT91_PIN_PA26) |
pin_to_mask(AT91_PIN_PA28),
&pioa->puer);
/* Initialize EMAC=MACB hardware */
at91_macb_hw_init();
}
static void macb_hw_init(void)
{
struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
struct at91_port *pioa = (struct at91_port *)ATMEL_BASE_PIOA;
struct at91_rstc *rstc = (struct at91_rstc *)ATMEL_BASE_RSTC;
unsigned long erstl;
/* Enable clock */
writel(1 << ATMEL_ID_EMAC0, &pmc->pcer);
/* Disable pull-ups to prevent PHY going into test mode */
writel(pin_to_mask(AT91_PIN_PA14) |
pin_to_mask(AT91_PIN_PA15) |
pin_to_mask(AT91_PIN_PA18),
&pioa->pudr);
/* Power down ethernet */
pca953x_set_dir(0x28, IO_EXP_ETH_POWER, PCA953X_DIR_OUT);
pca953x_set_val(0x28, IO_EXP_ETH_POWER, 1);
/* Hold ethernet in reset */
pca953x_set_dir(0x28, IO_EXP_ETH_RESET, PCA953X_DIR_OUT);
pca953x_set_val(0x28, IO_EXP_ETH_RESET, 0);
/* Enable ethernet power */
pca953x_set_val(0x28, IO_EXP_ETH_POWER, 0);
/* Need to reset PHY -> 500ms reset */
erstl = readl(&rstc->mr) & AT91_RSTC_MR_ERSTL_MASK;
writel(AT91_RSTC_KEY | AT91_RSTC_MR_ERSTL(13) |
AT91_RSTC_MR_URSTEN, &rstc->mr);
writel(AT91_RSTC_KEY | AT91_RSTC_CR_EXTRST, &rstc->cr);
/* Wait for end hardware reset */
while (!(readl(&rstc->sr) & AT91_RSTC_SR_NRSTL))
;
/* Restore NRST value */
writel(AT91_RSTC_KEY | erstl | AT91_RSTC_MR_URSTEN, &rstc->mr);
/* Bring the ethernet out of reset */
pca953x_set_val(0x28, IO_EXP_ETH_RESET, 1);
/* The phy internal reset take 21ms */
udelay(21 * 1000);
/* Re-enable pull-up */
writel(pin_to_mask(AT91_PIN_PA14) |
pin_to_mask(AT91_PIN_PA15) |
pin_to_mask(AT91_PIN_PA18),
&pioa->puer);
at91_macb_hw_init();
}
void at91_phy_reset(void)
{
unsigned long erstl;
unsigned long start = get_timer(0);
unsigned long const timeout = 1000; /* 1000ms */
at91_rstc_t *rstc = (at91_rstc_t *)ATMEL_BASE_RSTC;
erstl = readl(&rstc->mr) & AT91_RSTC_MR_ERSTL_MASK;
/*
* Need to reset PHY -> 500ms reset
* Reset PHY by pulling the NRST line for 500ms to low. To do so
* disable user reset for low level on NRST pin and poll the NRST
* level in reset status register.
*/
writel(AT91_RSTC_KEY | AT91_RSTC_MR_ERSTL(0x0D) |
AT91_RSTC_MR_URSTEN, &rstc->mr);
writel(AT91_RSTC_KEY | AT91_RSTC_CR_EXTRST, &rstc->cr);
/* Wait for end of hardware reset */
while (!(readl(&rstc->sr) & AT91_RSTC_SR_NRSTL)) {
/* avoid shutdown by watchdog */
WATCHDOG_RESET();
mdelay(10);
/* timeout for not getting stuck in an endless loop */
if (get_timer(start) >= timeout) {
puts("*** ERROR: Timeout waiting for PHY reset!\n");
break;
}
};
/* Restore NRST value */
writel(AT91_RSTC_KEY | erstl | AT91_RSTC_MR_URSTEN, &rstc->mr);
}
void at91_macb_hw_init(void)
{
at91_pmc_t *pmc = (at91_pmc_t *) ATMEL_BASE_PMC;
struct at91_rstc *rstc = (struct at91_rstc *)ATMEL_BASE_RSTC;
unsigned long erstl;
erstl = readl(&rstc->mr) & AT91_RSTC_MR_ERSTL_MASK;
/* Need to reset PHY -> 500ms reset */
writel(AT91_RSTC_KEY | AT91_RSTC_MR_ERSTL(13) |
AT91_RSTC_MR_URSTEN, &rstc->mr);
writel(AT91_RSTC_KEY | AT91_RSTC_CR_EXTRST, &rstc->cr);
/* Wait for end hardware reset */
while (!(readl(&rstc->sr) & AT91_RSTC_SR_NRSTL))
;
/* Restore NRST value */
writel(AT91_RSTC_KEY | erstl | AT91_RSTC_MR_URSTEN,
&rstc->mr);
if (has_emac0()) {
/* Enable EMAC0 clock */
writel(1 << ATMEL_ID_EMAC0, &pmc->pcer);
/* EMAC0 pins setup */
at91_set_a_periph(AT91_PIO_PORTB, 4, 0); /* ETXCK */
at91_set_a_periph(AT91_PIO_PORTB, 3, 0); /* ERXDV */
at91_set_a_periph(AT91_PIO_PORTB, 0, 0); /* ERX0 */
at91_set_a_periph(AT91_PIO_PORTB, 1, 0); /* ERX1 */
at91_set_a_periph(AT91_PIO_PORTB, 2, 0); /* ERXER */
at91_set_a_periph(AT91_PIO_PORTB, 7, 0); /* ETXEN */
at91_set_a_periph(AT91_PIO_PORTB, 9, 0); /* ETX0 */
at91_set_a_periph(AT91_PIO_PORTB, 10, 0); /* ETX1 */
at91_set_a_periph(AT91_PIO_PORTB, 5, 0); /* EMDIO */
at91_set_a_periph(AT91_PIO_PORTB, 6, 0); /* EMDC */
}
if (has_emac1()) {
/* Enable EMAC1 clock */
writel(1 << ATMEL_ID_EMAC1, &pmc->pcer);
/* EMAC1 pins setup */
at91_set_b_periph(AT91_PIO_PORTC, 29, 0); /* ETXCK */
at91_set_b_periph(AT91_PIO_PORTC, 28, 0); /* ECRSDV */
at91_set_b_periph(AT91_PIO_PORTC, 20, 0); /* ERXO */
at91_set_b_periph(AT91_PIO_PORTC, 21, 0); /* ERX1 */
at91_set_b_periph(AT91_PIO_PORTC, 16, 0); /* ERXER */
at91_set_b_periph(AT91_PIO_PORTC, 27, 0); /* ETXEN */
at91_set_b_periph(AT91_PIO_PORTC, 18, 0); /* ETX0 */
at91_set_b_periph(AT91_PIO_PORTC, 19, 0); /* ETX1 */
at91_set_b_periph(AT91_PIO_PORTC, 31, 0); /* EMDIO */
at91_set_b_periph(AT91_PIO_PORTC, 30, 0); /* EMDC */
}
#ifndef CONFIG_RMII
/* Only emac0 support MII */
if (has_emac0()) {
at91_set_a_periph(AT91_PIO_PORTB, 16, 0); /* ECRS */
at91_set_a_periph(AT91_PIO_PORTB, 17, 0); /* ECOL */
at91_set_a_periph(AT91_PIO_PORTB, 13, 0); /* ERX2 */
at91_set_a_periph(AT91_PIO_PORTB, 14, 0); /* ERX3 */
at91_set_a_periph(AT91_PIO_PORTB, 15, 0); /* ERXCK */
at91_set_a_periph(AT91_PIO_PORTB, 11, 0); /* ETX2 */
at91_set_a_periph(AT91_PIO_PORTB, 12, 0); /* ETX3 */
at91_set_a_periph(AT91_PIO_PORTB, 8, 0); /* ETXER */
}
#endif
}
static void stamp9G20_macb_hw_init(void)
{
struct at91_port *pioa = (struct at91_port *)ATMEL_BASE_PIOA;
struct at91_rstc *rstc = (struct at91_rstc *)ATMEL_BASE_RSTC;
unsigned long erstl;
/* Enable the PHY Chip via PA26 on the Stamp 2 Adaptor */
at91_set_gpio_output(AT91_PIN_PA26, 0);
/*
* Disable pull-up on:
* RXDV (PA17) => PHY normal mode (not Test mode)
* ERX0 (PA14) => PHY ADDR0
* ERX1 (PA15) => PHY ADDR1
* ERX2 (PA25) => PHY ADDR2
* ERX3 (PA26) => PHY ADDR3
* ECRS (PA28) => PHY ADDR4 => PHYADDR = 0x0
*
* PHY has internal pull-down
*/
writel(pin_to_mask(AT91_PIN_PA14) |
pin_to_mask(AT91_PIN_PA15) |
pin_to_mask(AT91_PIN_PA17) |
pin_to_mask(AT91_PIN_PA18) |
pin_to_mask(AT91_PIN_PA28),
&pioa->pudr);
erstl = readl(&rstc->mr) & AT91_RSTC_MR_ERSTL_MASK;
/* Need to reset PHY -> 500ms reset */
writel(AT91_RSTC_KEY | (AT91_RSTC_MR_ERSTL(13) &
~AT91_RSTC_MR_URSTEN), &rstc->mr);
writel(AT91_RSTC_KEY | AT91_RSTC_CR_EXTRST, &rstc->cr);
/* Wait for end of hardware reset */
unsigned long start = get_timer(0);
unsigned long timeout = 1000; /* 1000ms */
while (!(readl(&rstc->sr) & AT91_RSTC_SR_NRSTL)) {
/* avoid shutdown by watchdog */
WATCHDOG_RESET();
mdelay(10);
/* timeout for not getting stuck in an endless loop */
if (get_timer(start) >= timeout) {
puts("*** ERROR: Timeout waiting for PHY reset!\n");
break;
};
};
/* Restore NRST value */
writel(AT91_RSTC_KEY | erstl | AT91_RSTC_MR_URSTEN,
&rstc->mr);
/* Re-enable pull-up */
writel(pin_to_mask(AT91_PIN_PA14) |
pin_to_mask(AT91_PIN_PA15) |
pin_to_mask(AT91_PIN_PA17) |
pin_to_mask(AT91_PIN_PA18) |
pin_to_mask(AT91_PIN_PA28),
&pioa->puer);
/* Initialize EMAC=MACB hardware */
at91_macb_hw_init();
}
