static inline void uart_stm32_set_stopbits(struct device *dev, u32_t stopbits)
{
USART_TypeDef *UartInstance = UART_STRUCT(dev);
#ifdef CONFIG_LPUART_1
if (IS_LPUART_INSTANCE(UartInstance)) {
LL_LPUART_SetStopBitsLength(UartInstance, stopbits);
} else {
LL_USART_SetStopBitsLength(UartInstance, stopbits);
}
#else
LL_USART_SetStopBitsLength(UartInstance, stopbits);
#endif /* CONFIG_LPUART_1 */
}
/**
* @brief Initialize LPUART registers according to the specified
* parameters in LPUART_InitStruct.
* @note As some bits in LPUART configuration registers can only be written when the LPUART is disabled (USART_CR1_UE bit =0),
* LPUART IP should be in disabled state prior calling this function. Otherwise, ERROR result will be returned.
* @note Baud rate value stored in LPUART_InitStruct BaudRate field, should be valid (different from 0).
* @param LPUARTx LPUART Instance
* @param LPUART_InitStruct pointer to a @ref LL_LPUART_InitTypeDef structure
* that contains the configuration information for the specified LPUART peripheral.
* @retval An ErrorStatus enumeration value:
* - SUCCESS: LPUART registers are initialized according to LPUART_InitStruct content
* - ERROR: Problem occurred during LPUART Registers initialization
*/
ErrorStatus LL_LPUART_Init(USART_TypeDef *LPUARTx, LL_LPUART_InitTypeDef *LPUART_InitStruct)
{
ErrorStatus status = ERROR;
uint32_t periphclk = LL_RCC_PERIPH_FREQUENCY_NO;
/* Check the parameters */
assert_param(IS_LPUART_INSTANCE(LPUARTx));
assert_param(IS_LL_LPUART_BAUDRATE(LPUART_InitStruct->BaudRate));
assert_param(IS_LL_LPUART_DATAWIDTH(LPUART_InitStruct->DataWidth));
assert_param(IS_LL_LPUART_STOPBITS(LPUART_InitStruct->StopBits));
assert_param(IS_LL_LPUART_PARITY(LPUART_InitStruct->Parity));
assert_param(IS_LL_LPUART_DIRECTION(LPUART_InitStruct->TransferDirection));
assert_param(IS_LL_LPUART_HWCONTROL(LPUART_InitStruct->HardwareFlowControl));
/* LPUART needs to be in disabled state, in order to be able to configure some bits in
CRx registers. Otherwise (LPUART not in Disabled state) => return ERROR */
if (LL_LPUART_IsEnabled(LPUARTx) == 0U)
{
/*---------------------------- LPUART CR1 Configuration -----------------------
* Configure LPUARTx CR1 (LPUART Word Length, Parity and Transfer Direction bits) with parameters:
* - DataWidth: USART_CR1_M bits according to LPUART_InitStruct->DataWidth value
* - Parity: USART_CR1_PCE, USART_CR1_PS bits according to LPUART_InitStruct->Parity value
* - TransferDirection: USART_CR1_TE, USART_CR1_RE bits according to LPUART_InitStruct->TransferDirection value
*/
MODIFY_REG(LPUARTx->CR1,
(USART_CR1_M | USART_CR1_PCE | USART_CR1_PS | USART_CR1_TE | USART_CR1_RE),
(LPUART_InitStruct->DataWidth | LPUART_InitStruct->Parity | LPUART_InitStruct->TransferDirection));
/*---------------------------- LPUART CR2 Configuration -----------------------
* Configure LPUARTx CR2 (Stop bits) with parameters:
* - Stop Bits: USART_CR2_STOP bits according to LPUART_InitStruct->StopBits value.
*/
LL_LPUART_SetStopBitsLength(LPUARTx, LPUART_InitStruct->StopBits);
/*---------------------------- LPUART CR3 Configuration -----------------------
* Configure LPUARTx CR3 (Hardware Flow Control) with parameters:
* - HardwareFlowControl: USART_CR3_RTSE, USART_CR3_CTSE bits according to LPUART_InitStruct->HardwareFlowControl value.
*/
LL_LPUART_SetHWFlowCtrl(LPUARTx, LPUART_InitStruct->HardwareFlowControl);
/*---------------------------- LPUART BRR Configuration -----------------------
* Retrieve Clock frequency used for LPUART Peripheral
*/
periphclk = LL_RCC_GetLPUARTClockFreq(LL_RCC_LPUART1_CLKSOURCE);
/* Configure the LPUART Baud Rate :
- valid baud rate value (different from 0) is required
- Peripheral clock as returned by RCC service, should be valid (different from 0).
*/
if ((periphclk != LL_RCC_PERIPH_FREQUENCY_NO)
&& (LPUART_InitStruct->BaudRate != 0U))
{
status = SUCCESS;
LL_LPUART_SetBaudRate(LPUARTx,
periphclk,
LPUART_InitStruct->BaudRate);
/* Check BRR is greater than or equal to 0x300 */
assert_param(IS_LL_LPUART_BRR(LPUARTx->BRR));
}
}
return (status);
}