void __init nmdk_timer_init(void)
{
unsigned long rate;
struct clk *clk0;
u32 cr = MTU_CRn_32BITS;
clk0 = clk_get_sys("mtu0", NULL);
BUG_ON(IS_ERR(clk0));
clk_enable(clk0);
/*
* Tick rate is 2.4MHz for Nomadik and 2.4Mhz, 100MHz or 133 MHz
* for ux500.
* Use a divide-by-16 counter if the tick rate is more than 32MHz.
* At 32 MHz, the timer (with 32 bit counter) can be programmed
* to wake-up at a max 127s a head in time. Dividing a 2.4 MHz timer
* with 16 gives too low timer resolution.
*/
rate = clk_get_rate(clk0);
if (rate > 32000000) {
rate /= 16;
cr |= MTU_CRn_PRESCALE_16;
} else {
cr |= MTU_CRn_PRESCALE_1;
}
/* Timer 0 is the free running clocksource */
writel(cr, mtu_base + MTU_CR(0));
writel(0, mtu_base + MTU_LR(0));
writel(0, mtu_base + MTU_BGLR(0));
writel(cr | MTU_CRn_ENA, mtu_base + MTU_CR(0));
/* Now the clock source is ready */
nmdk_clksrc.read = nmdk_read_timer;
if (clocksource_register_hz(&nmdk_clksrc, rate))
pr_err("timer: failed to initialize clock source %s\n",
nmdk_clksrc.name);
init_sched_clock(&cd, nomadik_update_sched_clock, 32, rate);
/* Timer 1 is used for events */
clockevents_calc_mult_shift(&nmdk_clkevt, rate, MTU_MIN_RANGE);
writel(cr | MTU_CRn_ONESHOT, mtu_base + MTU_CR(1)); /* off, currently */
nmdk_clkevt.max_delta_ns =
clockevent_delta2ns(0xffffffff, &nmdk_clkevt);
nmdk_clkevt.min_delta_ns =
clockevent_delta2ns(0x00000002, &nmdk_clkevt);
nmdk_clkevt.cpumask = cpumask_of(0);
/* Register irq and clockevents */
setup_irq(IRQ_MTU0, &nmdk_timer_irq);
clockevents_register_device(&nmdk_clkevt);
}
void mtu_clocksource_reset(void)
{
writel(MTU_CRn_DIS, mtu0_base + MTU_CR(1));
/* ClockSource: configure load and background-load, and fire it up */
writel(u8500_cycle, mtu0_base + MTU_LR(1));
writel(u8500_cycle, mtu0_base + MTU_BGLR(1));
writel(MTU_CRn_PRESCALE_1 | MTU_CRn_32BITS | MTU_CRn_ENA |
MTU_CRn_FREERUNNING, mtu0_base + MTU_CR(1));
}
void nmdk_clksrc_reset(void)
{
writel(0, mtu_base + MTU_CR(0));
writel(nmdk_cycle, mtu_base + MTU_LR(0));
writel(nmdk_cycle, mtu_base + MTU_BGLR(0));
writel(clk_prescale | MTU_CRn_32BITS | MTU_CRn_ENA,
mtu_base + MTU_CR(0));
}
void nmdk_clksrc_reset(void)
{
/* Disable */
writel(0, mtu_base + MTU_CR(0));
/* ClockSource: configure load and background-load, and fire it up */
writel(nmdk_cycle, mtu_base + MTU_LR(0));
writel(nmdk_cycle, mtu_base + MTU_BGLR(0));
writel(clk_prescale | MTU_CRn_32BITS | MTU_CRn_ENA,
mtu_base + MTU_CR(0));
}
void nmdk_clkevt_reset(void)
{
if (clkevt_periodic) {
writel(nmdk_cycle, mtu_base + MTU_LR(1));
writel(nmdk_cycle, mtu_base + MTU_BGLR(1));
writel(MTU_CRn_PERIODIC | clk_prescale |
MTU_CRn_32BITS | MTU_CRn_ENA,
mtu_base + MTU_CR(1));
writel(1 << 1, mtu_base + MTU_IMSC);
} else {
(void) nmdk_clkevt_next(nmdk_cycle, NULL);
}
}
void nmdk_clkevt_reset(void)
{
if (clkevt_periodic) {
/* Timer: configure load and background-load, and fire it up */
writel(nmdk_cycle, mtu_base + MTU_LR(1));
writel(nmdk_cycle, mtu_base + MTU_BGLR(1));
writel(MTU_CRn_PERIODIC | clk_prescale |
MTU_CRn_32BITS | MTU_CRn_ENA,
mtu_base + MTU_CR(1));
writel(1 << 1, mtu_base + MTU_IMSC);
} else {
/* Generate an interrupt to start the clockevent again */
(void) nmdk_clkevt_next(nmdk_cycle, NULL);
}
}
void mtu_clockevent_reset(void)
{
if (mtu_periodic) {
/* Timer: configure load and background-load, and fire it up */
writel(u8500_cycle, mtu0_base + MTU_LR(0));
writel(u8500_cycle, mtu0_base + MTU_BGLR(0));
writel(MTU_CRn_PERIODIC | MTU_CRn_PRESCALE_1 |
MTU_CRn_32BITS | MTU_CRn_ENA,
mtu0_base + MTU_CR(0));
writel(1 << 0, mtu0_base + MTU_IMSC);
} else {
/* Generate an interrupt to start the clockevent again */
u8500_mtu_clkevt_next(u8500_cycle, NULL);
}
}
void __init nmdk_timer_init(void)
{
unsigned long rate;
struct clk *clk0;
struct clk *clk1;
u32 cr;
clk0 = clk_get_sys("mtu0", NULL);
BUG_ON(IS_ERR(clk0));
clk1 = clk_get_sys("mtu1", NULL);
BUG_ON(IS_ERR(clk1));
clk_enable(clk0);
clk_enable(clk1);
/*
* Tick rate is 2.4MHz for Nomadik and 110MHz for ux500:
* use a divide-by-16 counter if it's more than 16MHz
*/
cr = MTU_CRn_32BITS;;
rate = clk_get_rate(clk0);
if (rate > 16 << 20) {
rate /= 16;
cr |= MTU_CRn_PRESCALE_16;
} else {
cr |= MTU_CRn_PRESCALE_1;
}
clocksource_calc_mult_shift(&nmdk_clksrc, rate, MTU_MIN_RANGE);
/* Timer 0 is the free running clocksource */
writel(cr, mtu_base + MTU_CR(0));
writel(0, mtu_base + MTU_LR(0));
writel(0, mtu_base + MTU_BGLR(0));
writel(cr | MTU_CRn_ENA, mtu_base + MTU_CR(0));
/* Now the scheduling clock is ready */
nmdk_clksrc.read = nmdk_read_timer;
if (clocksource_register(&nmdk_clksrc))
pr_err("timer: failed to initialize clock source %s\n",
nmdk_clksrc.name);
/* Timer 1 is used for events, fix according to rate */
cr = MTU_CRn_32BITS;
rate = clk_get_rate(clk1);
if (rate > 16 << 20) {
rate /= 16;
cr |= MTU_CRn_PRESCALE_16;
} else {
cr |= MTU_CRn_PRESCALE_1;
}
clockevents_calc_mult_shift(&nmdk_clkevt, rate, MTU_MIN_RANGE);
writel(cr | MTU_CRn_ONESHOT, mtu_base + MTU_CR(1)); /* off, currently */
nmdk_clkevt.max_delta_ns =
clockevent_delta2ns(0xffffffff, &nmdk_clkevt);
nmdk_clkevt.min_delta_ns =
clockevent_delta2ns(0x00000002, &nmdk_clkevt);
nmdk_clkevt.cpumask = cpumask_of(0);
/* Register irq and clockevents */
setup_irq(IRQ_MTU0, &nmdk_timer_irq);
clockevents_register_device(&nmdk_clkevt);
}
