/**
* @brief Setup the microcontroller system.
* Initialize the Embedded Flash Interface, the PLL and update the
* SystemCoreClock variable.
* @param None
* @retval None
*/
void SystemInit (void)
{
/*!< Set MSION bit */
RCC->CR |= (uint32_t)0x00000100;
/*!< Reset SW[1:0], HPRE[3:0], PPRE1[2:0], PPRE2[2:0], MCOSEL[2:0] and MCOPRE[2:0] bits */
RCC->CFGR &= (uint32_t)0x88FFC00C;
/*!< Reset HSION, HSEON, CSSON and PLLON bits */
RCC->CR &= (uint32_t)0xEEFEFFFE;
/*!< Reset HSEBYP bit */
RCC->CR &= (uint32_t)0xFFFBFFFF;
/*!< Reset PLLSRC, PLLMUL[3:0] and PLLDIV[1:0] bits */
RCC->CFGR &= (uint32_t)0xFF02FFFF;
/*!< Disable all interrupts */
RCC->CIR = 0x00000000;
#ifdef DATA_IN_ExtSRAM
SystemInit_ExtMemCtl();
#endif /* DATA_IN_ExtSRAM */
#ifdef VECT_TAB_SRAM
SCB->VTOR = SRAM_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal SRAM. */
#else
SCB->VTOR = FLASH_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal FLASH. */
#endif
}
/**
* @brief Setup the microcontroller system
* Initialize the FPU setting, vector table location and External memory
* configuration.
* @param None
* @retval None
*/
void SystemInit(void)
{
/* FPU settings ------------------------------------------------------------*/
#if (__FPU_PRESENT == 1) && (__FPU_USED == 1)
SCB->CPACR |= ((3UL << 10*2)|(3UL << 11*2)); /* set CP10 and CP11 Full Access */
#endif
/* Reset the RCC clock configuration to the default reset state ------------*/
/* Set HSION bit */
RCC->CR |= (uint32_t)0x00000001;
/* Reset CFGR register */
RCC->CFGR = 0x00000000;
/* Reset HSEON, CSSON and PLLON bits */
RCC->CR &= (uint32_t)0xFEF6FFFF;
/* Reset PLLCFGR register */
RCC->PLLCFGR = 0x24003010;
/* Reset HSEBYP bit */
RCC->CR &= (uint32_t)0xFFFBFFFF;
/* Disable all interrupts */
RCC->CIR = 0x00000000;
#if defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
SystemInit_ExtMemCtl();
#endif /* DATA_IN_ExtSRAM || DATA_IN_ExtSDRAM */
}
void __Init_Data(void)
{
unsigned long *pulSrc, *pulDest;
pulSrc = &_sidata;
/* init HW (with clocks) before data/bss initalising ? */
for(pulDest = &_sdata; pulDest < &_edata; )
*(pulDest++) = *(pulSrc++);
for(pulDest = &_sbss; pulDest < &_ebss; )
*(pulDest++) = 0;
/* Init hardware before calling constructors */
init_HW();
#if 0
/* External memory bus initialisation */
SystemInit_ExtMemCtl();
#endif
/* Call constructors */
unsigned long *ctors;
for(ctors = &__ctors_start__; ctors < &__ctors_end__; )
((void(*)(void))(*ctors++))();
}
void SystemInit (void)
{
/* Reset the RCC clock configuration to the default reset state(for debug purpose) */
/* Set HSION bit */
RCC->CR |= (uint32_t)0x00000001;
/* Reset SW, HPRE, PPRE1, PPRE2, ADCPRE and MCO bits */
#ifndef STM32F10X_CL
RCC->CFGR &= (uint32_t)0xF8FF0000;
#else
RCC->CFGR &= (uint32_t)0xF0FF0000;
#endif /* STM32F10X_CL */
/* Reset HSEON, CSSON and PLLON bits */
RCC->CR &= (uint32_t)0xFEF6FFFF;
/* Reset HSEBYP bit */
RCC->CR &= (uint32_t)0xFFFBFFFF;
/* Reset PLLSRC, PLLXTPRE, PLLMUL and USBPRE/OTGFSPRE bits */
RCC->CFGR &= (uint32_t)0xFF80FFFF;
#ifdef STM32F10X_CL
/* Reset PLL2ON and PLL3ON bits */
RCC->CR &= (uint32_t)0xEBFFFFFF;
/* Disable all interrupts and clear pending bits */
RCC->CIR = 0x00FF0000;
/* Reset CFGR2 register */
RCC->CFGR2 = 0x00000000;
#elif defined (STM32F10X_LD_VL) || defined (STM32F10X_MD_VL) || (defined STM32F10X_HD_VL)
/* Disable all interrupts and clear pending bits */
RCC->CIR = 0x009F0000;
/* Reset CFGR2 register */
RCC->CFGR2 = 0x00000000;
#else
/* Disable all interrupts and clear pending bits */
RCC->CIR = 0x009F0000;
#endif /* STM32F10X_CL */
#if defined (STM32F10X_HD) || (defined STM32F10X_XL) || (defined STM32F10X_HD_VL)
#ifdef DATA_IN_ExtSRAM
SystemInit_ExtMemCtl();
#endif /* DATA_IN_ExtSRAM */
#endif
/* Configure the System clock frequency, HCLK, PCLK2 and PCLK1 prescalers */
/* Configure the Flash Latency cycles and enable prefetch buffer */
SetSysClock();
#ifdef VECT_TAB_SRAM
SCB->VTOR = SRAM_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal SRAM. */
#else
SCB->VTOR = FLASH_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal FLASH. */
#endif
}
/**
* @brief Setup the microcontroller system
* Initialize the Embedded Flash Interface, the PLL and update the SystemFrequency variable.
* @note This function should be used only after reset.
* @param None
* @retval None
*/
void SystemInit (void)
{
/* Reset the RCC clock configuration to the default reset state(for debug purpose) */
/* Set HSION bit */
RCC->CR |= (uint32_t)0x00000001;
/* Reset SW, HPRE, PPRE1, PPRE2, ADCPRE and MCO bits */
#ifndef STM32F10X_CL
RCC->CFGR &= (uint32_t)0xF8FF0000;
#else
RCC->CFGR &= (uint32_t)0xF0FF0000;
#endif /* STM32F10X_CL */
/* Reset HSEON, CSSON and PLLON bits */
RCC->CR &= (uint32_t)0xFEF6FFFF;
/* Reset HSEBYP bit */
RCC->CR &= (uint32_t)0xFFFBFFFF;
/* Reset PLLSRC, PLLXTPRE, PLLMUL and USBPRE/OTGFSPRE bits */
RCC->CFGR &= (uint32_t)0xFF80FFFF;
#ifndef STM32F10X_CL
/* Disable all interrupts and clear pending bits */
RCC->CIR = 0x009F0000;
#else
/* Reset PLL2ON and PLL3ON bits */
RCC->CR &= (uint32_t)0xEBFFFFFF;
/* Disable all interrupts and clear pending bits */
RCC->CIR = 0x00FF0000;
/* Reset CFGR2 register */
RCC->CFGR2 = 0x00000000;
#endif /* STM32F10X_CL */
/* Configure the System clock frequency, HCLK, PCLK2 and PCLK1 prescalers */
/* Configure the Flash Latency cycles and enable prefetch buffer */
SetSysClock();
#ifdef STM32F10X_HD
#ifdef DATA_IN_ExtSRAM
SystemInit_ExtMemCtl();
#endif /* DATA_IN_ExtSRAM */
#endif /* STM32F10X_HD */
}
/**
* @brief Setup the microcontroller system
* Initialize the FPU setting, vector table location and External memory
* configuration.
* @param None
* @retval None
*/
void SystemInit(void)
{
/* FPU settings ------------------------------------------------------------*/
#if (__FPU_PRESENT == 1) && (__FPU_USED == 1)
SCB->CPACR |= ((3UL << 10*2)|(3UL << 11*2)); /* set CP10 and CP11 Full Access */
#endif
/* Reset the RCC clock configuration to the default reset state ------------*/
/* Set HSION bit */
RCC->CR |= (uint32_t)0x00000001;
/* Reset CFGR register */
RCC->CFGR = 0x00000000;
/* Reset HSEON, CSSON and PLLON bits */
RCC->CR &= (uint32_t)0xFEF6FFFF;
/* Reset PLLCFGR register */
RCC->PLLCFGR = 0x24003010;
/* Reset HSEBYP bit */
RCC->CR &= (uint32_t)0xFFFBFFFF;
/* Disable all interrupts */
RCC->CIR = 0x00000000;
#if defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
SystemInit_ExtMemCtl();
#endif /* DATA_IN_ExtSRAM || DATA_IN_ExtSDRAM */
/* Configure the Vector Table location add offset address ------------------*/
#ifdef VECT_TAB_SRAM
SCB->VTOR = SRAM_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal SRAM */
#else
SCB->VTOR = NVIC_FLASH_VECTOR_ADDRESS | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal FLASH */
#endif
ublox_board_init();
}
void systemInit(bool overclock)
{
//RCC_ClocksTypeDef rccClocks;
int i;
// start fpu
SCB->CPACR = (0x3 << (10 * 2)) | (0x3 << (11 * 2));
/* Reset the RCC clock configuration to the default reset state ------------*/
/* Set HSION bit */
RCC->CR |= (uint32_t)0x00000001;
/* Reset CFGR register */
RCC->CFGR = 0x00000000;
/* Reset HSEON, CSSON and PLLON bits */
RCC->CR &= (uint32_t)0xFEF6FFFF;
/* Reset PLLCFGR register */
RCC->PLLCFGR = 0x24003010;
/* Reset HSEBYP bit */
RCC->CR &= (uint32_t)0xFFFBFFFF;
/* Disable all interrupts */
RCC->CIR = 0x00000000;
#ifdef DATA_IN_ExtSRAM
SystemInit_ExtMemCtl();
#endif /* DATA_IN_ExtSRAM */
/* Configure the System clock source, PLL Multiplier and Divider factors,
AHB/APBx prescalers and Flash settings ----------------------------------*/
SetSysClock();
#define VECT_TAB_OFFSET 0x00 /*!< Vector Table base offset field.
/* Configure the Vector Table location add offset address ------------------*/
#ifdef VECT_TAB_SRAM
SCB->VTOR = SRAM_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal SRAM */
#else
SCB->VTOR = FLASH_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal FLASH */
#endif
// Init cycle counter
cycleCounterInit();
// SysTick
SysTick_Config(SystemCoreClock / 1000);
// RCC_ADCCLKConfig(RCC_ADC12PLLCLK_Div256); // 72 MHz divided by 256 = 281.25 kHz
// Turn on peripherial clocks
// RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_ADC12, ENABLE);
// RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_DMA1, ENABLE); // USART1, USART2
// RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_DMA2, ENABLE); // ADC2
RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOA, ENABLE);
RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOB, ENABLE);
RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOC, ENABLE);
// RCC_APB1PeriphClockCmd(RCC_APB1Periph_SPI2, ENABLE);
RCC_APB2PeriphClockCmd(RCC_APB2Periph_SPI1, ENABLE);
RCC_APB2PeriphClockCmd(RCC_APB2Periph_TIM1, ENABLE);
RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM2, ENABLE); // PWM Out + PWM RX
RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM3, ENABLE); // PWM Out
RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM4, ENABLE); // PWM Out + PWM RX
RCC_APB1PeriphClockCmd(RCC_APB1Periph_I2C3, ENABLE); // i2c
RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM5, ENABLE); //
RCC_APB2PeriphClockCmd(RCC_APB2Periph_TIM8, ENABLE); //
RCC_APB2PeriphClockCmd(RCC_APB2Periph_TIM10, ENABLE); //
RCC_APB2PeriphClockCmd(RCC_APB2Periph_TIM11, ENABLE); //
RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM12, ENABLE); //
// RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM7, ENABLE); //
//
// PPM + PWM RX
// RCC_APB2PeriphClockCmd(RCC_APB2Periph_TIM8, ENABLE); //
// RCC_APB2PeriphClockCmd(RCC_APB2Periph_TIM15, ENABLE); // PWM Out
// RCC_APB2PeriphClockCmd(RCC_APB2Periph_TIM16, ENABLE); // PWM Out
// RCC_APB2PeriphClockCmd(RCC_APB2Periph_TIM17, ENABLE); // PWM Out
// RCC_APB2PeriphClockCmd(RCC_APB2Periph_USART1, ENABLE); // Telemetry
// RCC_APB1PeriphClockCmd(RCC_APB1Periph_USART2, ENABLE); // GPS
// RCC_APB1PeriphClockCmd(RCC_APB1Periph_USART3, ENABLE); // Spektrum RX
RCC_ClearFlag();
NVIC_PriorityGroupConfig(NVIC_PriorityGroup_2); // 2 bits for pre-emption priority, 2 bits for subpriority
gpioStart();
spiInit();
// if feature(FEATURE_I2C)
// i2cInit(I2C2);
for (i = 0; i < 10; i++) {
LED0_TOGGLE
delay(25);
BEEP_ON
delay(25);
BEEP_OFF
}
LED0_OFF
}
