C++ (Cpp) USB_Interrupts_Config示例

示例#1

文件： main.c 项目： IvanOrfanidi/STM32-Tests-Project

int main()
{
  InitGPIO();

  InitBKP();
  
  Set_System();
  Set_USBClock();
  USB_Interrupts_Config();
  USB_Init();
  
  
  rtc_init();
  /*
  RTC_t date;
  date.year = 2015;
  date.month = 10;
  date.mday = 24;
  
  date.hour = 23;
  date.min = 20;
  date.sec = 0;
  rtc_settime(&date);
  */
  
  // Start Task //
  xTaskCreate(vLcdTask, "vLcdTask", configMINIMAL_STACK_SIZE * 1, NULL, tskIDLE_PRIORITY + 1, &xHandleLcdTask);
  xTaskCreate(vDebugTask, "vDebugTask", configMINIMAL_STACK_SIZE * 1, NULL, tskIDLE_PRIORITY + 1, &xHandleDebugTask);
  
  // Start scheduler //
  osKernelStart(NULL, NULL);
}

示例#2

文件： main.c 项目： eiva/Quadro

/*******************************************************************************
* Function Name  : main.
* Description    : main routine.
* Input          : None.
* Output         : None.
* Return         : None.
*******************************************************************************/
int main(void)
{
  Set_System();

  USB_Interrupts_Config();

  Set_USBClock();

  USB_Init();

  uint16_t counter = 0;

  while (1)
  {
	  TheReport.SAX = 32768;
	  TheReport.SAY = counter;
	  ++counter;
	  if (bDeviceState == CONFIGURED)
	  {
		  if (PrevXferComplete)
	      {
	          RHIDCheckState();
	      }
	  }
  }
}

示例#3

文件： usb_misc.c 项目： ledono/touchscreen-apps

/**
 * @brief  Configure the USB in CDC mode.
 * @retval None
 */
void initUSB_CDC(void) {
    Set_System();
    Set_USBClock();
    USB_Interrupts_Config();
    USB_Init_Dynamic(&Device_Property_CDC, &User_Standard_Requests_CDC);
    // now device state is UNCONNECTED
}

示例#4

文件： main.c 项目： skt041959/stm32-template

int main()
{
    SysTick_Config(SystemCoreClock/1000);
    GPIO_PinRemapConfig(GPIO_Remap_SWJ_JTAGDisable,ENABLE);
    Set_System();
    Set_USBClock();
    USB_Interrupts_Config();
    USB_Init();

/*
 *    GPIO_Config();
 *
 *    GPIOA->BSRR = GPIO_Pin_15;
 *
 *    while (1)
 *    {
 *        if (bDeviceState == CONFIGURED) {
 *            CDC_Receive_DATA();
 *            [>Check to see if we have data yet <]
 *            if (Receive_length != 0) {
 *                if (packet_sent == 1)
 *                    CDC_Send_DATA((unsigned char*) Receive_Buffer, Receive_length);
 *                Receive_length = 0;
 *            }
 *        }
 *    }
 */
    while(1);
}

示例#5

文件： main.c 项目： 1847123212/serprog-stm32-gd32

 int main(void)
 { 
	delay_init();	    	 //延时函数初始化	  
	uart_init(9600);	 	//串口初始化为9600
	LED_Init();		  		//初始化与LED连接的硬件接口
	 LED0=1;
	 LED1=1;
	LED2=1;
	USB_Cable_Config (ENABLE); 
	delay_ms(500);
	USB_Port_Set(0); 	
	delay_ms(500);
	USB_Port_Set(1);	
 	Set_USBClock();   
 	USB_Interrupts_Config();    
 	USB_Init();	 	 
	 	 	
	SPI_IO_Init(); 
	DMA_configuration();
	spi_conf(SPI_DEFAULT_SPEED);
	LED1=0;
	LED2=0;
	while(1)
	{	
		/* Get command */
    serprog_handle_command(usb_getc());
    /* Flush output via USB */
    usb_sync();		
	}
}

示例#6

文件： main.c 项目： IvanOrfanidi/STM32-Tests-Project

int main()
{
  InitGPIO();
  //InitTIM3();
  //InitTIM4();

  InitIWDG();    // Init Watch Dog 
  InitBKP();
  
#ifdef DEBUG_OUTPUT_USB
  Set_System();
  Set_USBClock();
  USB_Interrupts_Config();
  USB_Init();
#else
  rtc_init();
#endif
  
  RTC_t date;
  date.year = 2015;
  date.month = 10;
  date.mday = 24;
  
  date.hour = 23;
  date.min = 20;
  date.sec = 0;
  rtc_settime(&date);
  
  // Start Task //
  xTaskCreate(vLcdPcf, "vLcdPcf", configMINIMAL_STACK_SIZE * 2, NULL, tskIDLE_PRIORITY + 1, &xHandlevLcdPcfTask);
  xTaskCreate(vDebugTask, "vDebugTask", configMINIMAL_STACK_SIZE * 2, NULL, tskIDLE_PRIORITY + 1, &xHandleDebugTask);
  
  // Start scheduler //
  osKernelStart(NULL, NULL);
}

示例#7

文件： main.c 项目： thegeek82000/rlc-meter-balmer-1

void USB_Config(void)
{
	Set_USBClock();
	USB_Interrupts_Config();
	USB_Init();
	// while (bDeviceState != CONFIGURED) {}
}

示例#8

文件： main.c 项目： 91thUb/usb-miner

/*******************************************************************************
* Function Name  : main.
* Description    : Main routine.
* Input          : None.
* Output         : None.
* Return         : None.
*******************************************************************************/
int main(void)
{
    int i;
    Reset_GC3355();
    Set_System();
    Set_USBClock();
    USB_Interrupts_Config();
#ifdef USE_USB_AS_HOST_IF	
    USB_Init();
#endif	
	  USART_Config_Default();
    btc_ltc_uart_config(115200);
    delay_init(72);
    //gpio_init();
    Timerx_Init(100,7200-1);
    USART_Config_Default();
    rx_cx_buffers_init();
    while (1)
    {
        dispatch_host_cmd();
        report_nonce_to_host();
        if(timer_count > 100) {
		timer_count = 0;
		//PR_DEBUG("GPIOB8 = %d\n",GPIO_ReadInputDataBit(GPIOB, GPIO_Pin_8));
		led1_revert();
		//PR_DEBUG("%02X\n",get_next_n_out(&usb_trans_buffer,152));
		//PR_DEBUG("has cmd length = %d\n",trans_buffer_has_cmd(&usb_trans_buffer));
        }
        //delay_ms(1000);
        //PR_DEBUG("delay 1000ms \n");
    }
}

示例#9

文件： main.c 项目： MBARM/MatchboxARM

/*******************************************************************************
* Function Name  : main.
* Descriptioan    : Main routine.
* Input          : None.
* Output         : None.
* Return         : None.
*******************************************************************************/
int main(void)
{
    int i;

    /* Set the Vector Table base adress at 0x8004000 */
    NVIC_SetVectorTable(NVIC_VectTab_FLASH, 0x4000);
    
    // Disable JTAG not the SWD  
    RCC_APB2PeriphClockCmd( RCC_APB2Periph_AFIO , ENABLE);      
    GPIO_PinRemapConfig(GPIO_Remap_SWJ_JTAGDisable, ENABLE);  
  
    Set_System();
    Set_USBClock();
    USB_Interrupts_Config();
    USB_Init();
    
    for(i = 0; i < 27; i++) TestBuffer[i] = i % 9;  
    
    while (1)
    {
        if (bDeviceState == CONFIGURED)
        {
            //CDC_Send_DATA ((unsigned char*)TestBuffer,27);
            //Delay(0xFFF);         
            CDC_Receive_DATA();
            // Check to see if we have data yet
            if (Receive_length  != 0)
            {
                if (packet_sent == 1)
                CDC_Send_DATA ((unsigned char*)Receive_Buffer,Receive_length);
                Receive_length = 0;
            }
        }
    }
} 

示例#10

文件： main.c 项目： HamsterReserved/STM32-NAND-Programmer

/*******************************************************************************
* Function Name  : main.
* Description    : main routine.
* Input          : None.
* Output         : None.
* Return         : None.
*******************************************************************************/
int main(void)
{
  GPIO_InitTypeDef GPIO_InitStructure;
	NAND_IDTypeDef NAND_Id;
	NAND_ADDRESS NAND_Address;
	int i=0;
#ifdef DEBUG
  debug();
#endif

  Set_System();
  RCC_AHBPeriphClockCmd(RCC_AHBPeriph_FSMC, ENABLE);
  
  Serial_Init();

    NAND_Init();
		NAND_Reset();
  NAND_ReadID(&NAND_Id);

  Get_Medium_Characteristics();
  Set_USBClock();
  USB_Interrupts_Config(); 
  GPIO_InitStructure.GPIO_Pin = GPIO_Pin_13;
  GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
  GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_OD;
  GPIO_Init(GPIOC, &GPIO_InitStructure);
  USB_Init();
	
  while (1)
  {	

  }
}

示例#11

文件： stm32l_virtual_uart.c 项目： GlennVDLocht/dash7-ap-open-source-stack

void uart_init() {
    Set_System();
    Set_USBClock();
    USB_Interrupts_Config();

    USB_Init();

}

示例#12

文件： Usb_App.c 项目： RTOS-Developers/TRTOS

void USB_Configs()
{
	RCC_APB2PeriphClockCmd(RCC_APB2Periph_AFIO, ENABLE); 
	USB_Cable_Config(ENABLE);
	USB_Interrupts_Config();    
	Set_USBClock();  
	USB_Init();	
}

示例#13

文件： usb.c 项目： jackeyjiang/3DPrinter-firmware

void USBDevice_Connect()
{
    DBG_MSG("called", 0);
    if(!InitMemoryInfo())
        return;
    USB_Interrupts_Config(ENABLE);
    USB_Cable_Config(ENABLE);
    USB_Init();
}

示例#14

文件： VCP_F3.c 项目： weiserj/stm32f3DiscoveryVcp

/*********************************************************************************************
Function name   : VCP_Init
Author 					: Grant Phillips
Date Modified   : 10/04/2014
Compiler        : Keil ARM-MDK (uVision V4.70.0.0)

Description			: Initializes the Virtual COM Port module

Special Note(s) : NONE

Parameters			: NONE
Return value		: NONE
*********************************************************************************************/
void VCP_Init(void)
{
  Set_System();
  Set_USBClock();
  USB_Interrupts_Config();		
  USB_Init();
	
	packet_sent=1;
}

示例#15

文件： usbtask.c 项目： FlameN/STM32RUNO

void vUSBTask(void *pvParameters)
{
	uint16 usbsize;
	uint8 usbbuf[256];
	//uint8 usbbufsizes[100];
	CONTENTS stru[100];
	uint16 usbbufsizesCounter=0;
	bool st = false;
	/* The parameters are not used. */
	(void) pvParameters;
/*
	uint16_t bufff[20];
	bufff[0] = 0x555;
	bufff[1] = 0x444;
	bufff[2] = 0x333;
	bufff[3] = 0x222;
	bufff[4] = 0x111;

	FLASH_ErasePage(DEVICE_FLASHMEM_LOCATION);
	//FLASH_ProgramHalfWord(DEVICE_FLASHMEM_LOCATION,bufff[0]);

	//FLASH_ProgramHalfWord(DEVICE_FLASHMEM_LOCATION+0x02,bufff[1]);
	//FLASH_ProgramHalfWord(DEVICE_FLASHMEM_LOCATION+0x04,bufff[2]);
	//FLASH_ProgramHalfWord(DEVICE_FLASHMEM_LOCATION+0x06,bufff[3]);
	//FLASH_ProgramHalfWord(DEVICE_FLASHMEM_LOCATION+0x08,bufff[4]);
	WriteFlash( bufff,(void*)(DEVICE_FLASHMEM_LOCATION),  10);*/
	//vTaskDelay(15000);
	  Set_USBClock();
	  USB_Interrupts_Config();
	  USB_Init();
int heapSize = 0;
	  while (1)
	  {
			heapSize = xPortGetFreeHeapSize();
							heapSize +=0;
		  usbsize = UsbReceiveData(usbbuf,256);

		  if(usbsize > 0)
		  {

			  stru[usbbufsizesCounter].buf[0]=usbbuf[0];
			  stru[usbbufsizesCounter].buf[1]=usbbuf[1];
			  stru[usbbufsizesCounter].buf[2]=usbbuf[2];
			  stru[usbbufsizesCounter].buf[3]=usbbuf[3];
			  stru[usbbufsizesCounter].size = usbsize;
			  usbbufsizesCounter++;
			  if(usbbufsizesCounter>=100) usbbufsizesCounter = 0;
			  usbsize = RVnetSlaveProcess(usbbuf,usbsize,1);
			  if(usbsize > 0)
			  {
				  UsbSendData(usbbuf,usbsize);
			  }
		  }
		  vTaskDelay(1);
	  }
}

示例#16

文件： serial_usb_vcp.c 项目： 4712betaflight/betaflight

serialPort_t *usbVcpOpen(void)
{
    vcpPort_t *s;

    IOInit(IOGetByTag(IO_TAG(PA11)), OWNER_USB, 0);
    IOInit(IOGetByTag(IO_TAG(PA12)), OWNER_USB, 0);

#if defined(STM32F4)
    usbGenerateDisconnectPulse();

    switch (usbDevConfig()->type) {
#ifdef USE_USB_CDC_HID
    case COMPOSITE:
        USBD_Init(&USB_OTG_dev, USB_OTG_FS_CORE_ID, &USR_desc, &USBD_HID_CDC_cb, &USR_cb);
        break;
#endif
    default:
        USBD_Init(&USB_OTG_dev, USB_OTG_FS_CORE_ID, &USR_desc, &USBD_CDC_cb, &USR_cb);
        break;
    }
#elif defined(STM32F7)
    usbGenerateDisconnectPulse();

    /* Init Device Library */
    USBD_Init(&USBD_Device, &VCP_Desc, 0);

    /* Add Supported Class */
    switch (usbDevConfig()->type) {
#ifdef USE_USB_CDC_HID
    case COMPOSITE:
    	USBD_RegisterClass(&USBD_Device, USBD_HID_CDC_CLASS);
        break;
#endif
    default:
        USBD_RegisterClass(&USBD_Device, USBD_CDC_CLASS);
        break;
    }

    /* HID Interface doesn't have any callbacks... */
    /* Add CDC Interface Class */
    USBD_CDC_RegisterInterface(&USBD_Device, &USBD_CDC_fops);

    /* Start Device Process */
    USBD_Start(&USBD_Device);
#else
    Set_System();
    Set_USBClock();
    USB_Init();
    USB_Interrupts_Config();
#endif

    s = &vcpPort;
    s->port.vTable = usbVTable;

    return (serialPort_t *)s;
}

示例#17

文件： usb_hid.c 项目： M-Reimer/IRMP_STM32

void USB_HID_Init(void)
{
	bDeviceState=UNCONNECTED;
	USB_HID_RecData_Ready = 0;
	USB_HID_RecData_Len = 0;
	Set_System();
	USB_Interrupts_Config();
	Set_USBClock();
	USB_Init();
}

示例#18

文件： main.c 项目： suxiaocheng/stm32_usb_hid

/*******************************************************************************
* Function Name  : main.
* Description    : Main routine.
* Input          : None.
* Output         : None.
* Return         : None.
*******************************************************************************/
int main(void)
{
	Set_System();
	Set_USBClock();
	USB_Interrupts_Config();
	USB_Init();

	while (1) {
	}
}

示例#19

文件： main.c 项目： margguo/DAQ

/**
  * @brief  Configure the USB.
  * @param  None
  * @retval None
  */
void Demo_USB (void)
{
  Set_System();
  Set_USBClock();
  USB_Interrupts_Config();
  
  USB_Init();

  while ((bDeviceState != CONFIGURED)&&(USBConnectTimeOut != 0))
  {}
}

示例#20

文件： usbComm.c 项目： RomainTT/SheldonProject

/**
	* @brief	Configure the usb serial communication.
	*					Blocking function.
	* @param 	Void
	* @return Void
	*/
void usbCommInit( void )
{
	
	Set_System();
  Set_USBClock();
  USB_Interrupts_Config();
  USB_Init();
	while (USB_GetState() != CONFIGURED) {} // Wait USB is ready
	
	usbCommInitPeriodicSending();
}

示例#21

文件： main.c 项目： htol/ultramicron

/*******************************************************************************
* Function Name  : main.
* Description    : Main routine.
* Input          : None.
* Output         : None.
* Return         : None.
*******************************************************************************/
int main(void)
{  NVIC_SetVectorTable(NVIC_VectTab_FLASH,0x3000);
  Set_System();
  Set_USBClock();
  USB_Interrupts_Config();
  USB_Init();
  
  while (1)
  {
  }
}

示例#22

文件： PCUsart.c 项目： joe3501/BlueRing

void PCUsart_Init(void)
{
	Set_USBClock();
	USB_Interrupts_Config();
	USB_Init();

	//g_pcCommand.CmdBuffer	= g_receive_buff;
	//g_com_handle_flag = 0;

	//reset_command();
}

示例#23

文件： main.c 项目： cedar-renjun/usb_msd_bootloader

void ResetUSB(void)
{
    delay_ms(500);
    // Reset USB
    usb_port_set(0);
    delay_ms(500);
    usb_port_set(1);
    USB_Interrupts_Config();
    Set_USBClock();
    USB_Init();
}

示例#24

/*******************************************************************************
* Function Name  : main.
* Description    : Main routine.
* Input          : None.
* Output         : None.
* Return         : None.
*******************************************************************************/
int main(void)
{
  Set_System();
  Set_USBClock();
  USB_Interrupts_Config();
  USB_Init();
  while (bDeviceState != CONFIGURED);

  while (1)
  {}
}

示例#25

文件： main.c 项目： mambrus/bitfire

/*******************************************************************************
* Function Name  : main
* Description    : main program.
* Input          : None.
* Return         : None.
*******************************************************************************/
int main(void)
{
  #ifdef DEBUG
  debug();
  #endif
  
  Set_System();
  Set_USBClock();
  USB_Interrupts_Config();
  USB_Init();
  /* Main loop */
	while(1);
}

示例#26

文件： serial_usb_vcp.c 项目： pqueiros/Triflight

serialPort_t *usbVcpOpen(void)
{
    vcpPort_t *s;

    Set_System();
    Set_USBClock();
    USB_Interrupts_Config();
    USB_Init();

    s = &vcpPort;
    s->port.vTable = usbVTable;

    return (serialPort_t *)s;
}

示例#27

文件： main.c 项目： 2thetop/XRange

int main( void )
{

  Set_System();
  Set_USBClock();
  USB_Interrupts_Config();
  USB_Init();

  RadioStart();

#ifdef __GNUC__
    return 0;
#endif
}

示例#28

文件： cdc_serial.c 项目： dtyangcm/rtt-stm32f103c8

void usb_init()
{
#ifdef RT_USING_STD_USB
    /* usb device controller driver initilize */
	Set_System();
	Set_USBClock();
	USB_Interrupts_Config();
	rt_usb_serial_init();
	USB_Init();
#ifdef RT_USING_CONSOLE
		//rt_console_set_device("vcom");
		//finsh_set_device( "vcom" );
#endif
#endif
}

示例#29

文件： usb_stm32f30x.c 项目： robert-b/baseflight

serialPort_t *usbInit(void)
{
    uartPort_t *s;

    Set_System();
    Set_USBClock();
    USB_Interrupts_Config();
    USB_Init();
    init_printf(NULL, usbPrintf);

    s = &uartPortUSB;
    s->port.vTable = usbVTable;

    return (serialPort_t *)s;

}

示例#30

文件： main.c 项目： zapol/compression-meter

int main(void)
{
    Set_System();
    SysTick_Config(SystemCoreClock/10000);
    Set_USBClock();
    USB_Interrupts_Config();
    USB_Init();

    lcdInit();

    volatile int x;
    while (1)
    {
        lcdSetBklight(sysTicks%10000/100);
        x++;
    }
}