示例#1
0
int uhd_device::set_rates(double tx_rate, double rx_rate)
{
	double offset_limit = 1.0;
	double tx_offset, rx_offset;

	// B2XX is the only device where we set FPGA clocking
	if (dev_type == B2XX) {
		if (set_master_clk(B2XX_CLK_RT) < 0)
			return -1;
	}

	// Set sample rates
	try {
		usrp_dev->set_tx_rate(tx_rate);
		usrp_dev->set_rx_rate(rx_rate);
	} catch (const std::exception &ex) {
		LOG(ALERT) << "UHD rate setting failed";
		LOG(ALERT) << ex.what();
		return -1;
	}
	this->tx_rate = usrp_dev->get_tx_rate();
	this->rx_rate = usrp_dev->get_rx_rate();

	tx_offset = fabs(this->tx_rate - tx_rate);
	rx_offset = fabs(this->rx_rate - rx_rate);
	if ((tx_offset > offset_limit) || (rx_offset > offset_limit)) {
		LOG(ALERT) << "Actual sample rate differs from desired rate";
		LOG(ALERT) << "Tx/Rx (" << this->tx_rate << "/"
			   << this->rx_rate << ")";
		return -1;
	}

	return 0;
}
示例#2
0
int setup_device(uhd::usrp::multi_usrp::sptr usrp, double rx_gain, double tx_gain, double freq, double rate){

    //create a usrp device
    std::cout << boost::format("Using Device: %s") % usrp->get_pp_string() << std::endl;

    usrp->set_rx_rate(rate);
    usrp->set_rx_freq(freq);
    usrp->set_rx_gain(rx_gain);
	usrp->set_tx_rate(rate);
	usrp->set_tx_freq(freq);
	usrp->set_tx_gain(tx_gain);

}
示例#3
0
void init_usrp() {
	cout << "Initial USRP" << endl;
	
	usrp = uhd::usrp::multi_usrp::make(usrp_ip);
	usrp->set_rx_rate(rate);
	usrp->set_tx_rate(rate);

	usrp->set_rx_freq(freq);
	usrp->set_tx_freq(freq);

	usrp->set_rx_gain(gain);
	uhd::meta_range_t rx_range = usrp->get_rx_gain_range();
}
double uhd_device::set_rates(double rate)
{
	double actual_rt, actual_clk_rt;

#if !defined(MULTICHAN) & !defined(RESAMPLE)
	// Make sure we can set the master clock rate on this device
	actual_clk_rt = usrp_dev->get_master_clock_rate();
	if (actual_clk_rt > U1_DEFAULT_CLK_RT) {
		LOG(ALERT) << "Cannot set clock rate on this device";
		LOG(ALERT) << "Please compile with host resampling support";
		return -1.0;
	}

	// Set master clock rate
	usrp_dev->set_master_clock_rate(master_clk_rt);
	actual_clk_rt = usrp_dev->get_master_clock_rate();

	if (actual_clk_rt != master_clk_rt) {
		LOG(ALERT) << "Failed to set master clock rate";
		LOG(ALERT) << "Actual clock rate " << actual_clk_rt;
		return -1.0;
	}
#endif

	// Set sample rates
	usrp_dev->set_tx_rate(rate);
	usrp_dev->set_rx_rate(rate);
	actual_rt = usrp_dev->get_tx_rate();

	if (actual_rt != rate) {
		LOG(ALERT) << "Actual sample rate differs from desired rate";
		LOG(ALERT) << actual_rt << "Hz";
		return -1.0;
	}
	if (usrp_dev->get_rx_rate() != actual_rt) {
		LOG(ALERT) << "Transmit and receive sample rates do not match";
		return -1.0;
	}

	return actual_rt;
}
示例#5
0
int setupUSRP(  uhd::usrp::multi_usrp::sptr&  usrp,
                const float                   center_freq,
                const float                   sample_rate,
                const int                     rx_gain,
                const char*                   dev_addr)
{
  //Initialize the USRP to the specified address
  usrp = uhd::usrp::multi_usrp::make(string(dev_addr));
  //Define the clock reference
  usrp->set_clock_source(__USRP_CLK_SRC);

  //Output some useful information
  cout  << "Using the following USRP device: " << endl
        << usrp->get_pp_string() << endl;

  //Try setting the sample rate.  If the rate we get is not the same as the
  //requested rate, we will return with a warning to ensure the user is aware
  //of the actual sample rate
  usrp->set_rx_rate( sample_rate );

  if( usrp->get_rx_rate() != sample_rate )
  {
    ios_base::fmtflags originalFlags = cout.flags();
    cout.setf(ios_base::left,ios_base::floatfield);
    cout.precision(15);
    cout  << "WARNING! Requested rate = " << sample_rate << endl
          << "WARNING! Actual rate = " << usrp->get_rx_rate() << endl;
    cout.setf(originalFlags);
  }

  //Try setting the center frequency.  Like above, if we get a different
  //frequency than the one we're requesting, we will spit out a warning for the
  //user
  usrp->set_rx_freq( center_freq );

  if( usrp->get_rx_freq() != center_freq )
  {
    ios_base::fmtflags originalFlags = cout.flags();
    cout.setf(ios_base::left,ios_base::floatfield);
    cout.precision(15);
    cout  << "WARNING! Requested frequency = " << center_freq << endl
          << "WARNING! Actual frequency = " << usrp->get_rx_freq() << endl;
    cout.setf(originalFlags);
  }

  //Set the RX gain.  There really shouldn't be any problems here, but the user
  //might request something silly like 50dB of gain when the module can't
  //accomodate.  So we'll perform a similar check here.
  usrp->set_rx_gain( rx_gain );

  if( usrp->get_rx_gain() != rx_gain )
  {
    cout  << "WARNING! Requested gain = " << rx_gain << endl
          << "WARNING! Actual gain = " << usrp->get_rx_gain() << endl;
  }

  //Ensure the LO locked
  vector<string> sensor_names;
  sensor_names = usrp->get_rx_sensor_names(0);
  if( find(sensor_names.begin(), sensor_names.end(), "lo_locked")
      != sensor_names.end() )
  {
    uhd::sensor_value_t lo_locked = usrp->get_rx_sensor("lo_locked",0);
    cout  << "Checking RX: " << endl
          << lo_locked.to_pp_string() << endl;
    UHD_ASSERT_THROW(lo_locked.to_bool());      //We should probably catch this
  }

  return 1;
}
示例#6
-1
/***********************************************************************
 * Set standard defaults for devices
 **********************************************************************/
static inline void set_optimum_defaults(uhd::usrp::multi_usrp::sptr usrp){
    uhd::property_tree::sptr tree = usrp->get_device()->get_tree();
    // Will work on 1st subdev, top-level must make sure it's the right one
    uhd::usrp::subdev_spec_t subdev_spec = usrp->get_rx_subdev_spec();

    const uhd::fs_path mb_path = "/mboards/0";
    const std::string mb_name = tree->access<std::string>(mb_path / "name").get();
    if (mb_name.find("USRP2") != std::string::npos or mb_name.find("N200") != std::string::npos or mb_name.find("N210") != std::string::npos  or mb_name.find("X300") != std::string::npos  or mb_name.find("X310") != std::string::npos){
        usrp->set_tx_rate(12.5e6);
        usrp->set_rx_rate(12.5e6);
    }
    else if (mb_name.find("B100") != std::string::npos){
        usrp->set_tx_rate(4e6);
        usrp->set_rx_rate(4e6);
    }
    else if (mb_name.find("E100") != std::string::npos or mb_name.find("E110") != std::string::npos){
        usrp->set_tx_rate(4e6);
        usrp->set_rx_rate(8e6);
    }
    else{
        throw std::runtime_error("self-calibration is not supported for this hardware");
    }

    const uhd::fs_path tx_fe_path = "/mboards/0/dboards/" + subdev_spec[0].db_name + "/tx_frontends/0";
    const std::string tx_name = tree->access<std::string>(tx_fe_path / "name").get();
    if (tx_name.find("WBX") != std::string::npos){
        usrp->set_tx_gain(0);
    }
    else if (tx_name.find("SBX") != std::string::npos){
        usrp->set_tx_gain(0);
    }
    else if (tx_name.find("CBX") != std::string::npos){
        usrp->set_tx_gain(0);
    }
    else if (tx_name.find("RFX") != std::string::npos){
        usrp->set_tx_gain(0);
    }
    else{
        throw std::runtime_error("self-calibration is not supported for this hardware");
    }

    const uhd::fs_path rx_fe_path = "/mboards/0/dboards/" + subdev_spec[0].db_name + "/rx_frontends/0";
    const std::string rx_name = tree->access<std::string>(rx_fe_path / "name").get();
    if (rx_name.find("WBX") != std::string::npos){
        usrp->set_rx_gain(25);
    }
    else if (rx_name.find("SBX") != std::string::npos){
        usrp->set_rx_gain(25);
    }
    else if (rx_name.find("CBX") != std::string::npos){
        usrp->set_rx_gain(25);
    }
    else if (rx_name.find("RFX") != std::string::npos){
        usrp->set_rx_gain(25);
    }
    else{
        throw std::runtime_error("self-calibration is not supported for this hardware");
    }

}