int SkirtBrim::generatePrimarySkirtBrimLines(const coord_t start_distance, size_t primary_line_count, const coord_t primary_extruder_minimal_length, const Polygons& first_layer_outline, Polygons& skirt_brim_primary_extruder)
{
const Settings& adhesion_settings = Application::getInstance().current_slice->scene.current_mesh_group->settings.get<ExtruderTrain&>("adhesion_extruder_nr").settings;
const coord_t primary_extruder_skirt_brim_line_width = adhesion_settings.get<coord_t>("skirt_brim_line_width") * adhesion_settings.get<Ratio>("initial_layer_line_width_factor");
coord_t offset_distance = start_distance - primary_extruder_skirt_brim_line_width / 2;
for (unsigned int skirt_brim_number = 0; skirt_brim_number < primary_line_count; skirt_brim_number++)
{
offset_distance += primary_extruder_skirt_brim_line_width;
Polygons outer_skirt_brim_line = first_layer_outline.offset(offset_distance, ClipperLib::jtRound);
//Remove small inner skirt and brim holes. Holes have a negative area, remove anything smaller then 100x extrusion "area"
for (unsigned int n = 0; n < outer_skirt_brim_line.size(); n++)
{
double area = outer_skirt_brim_line[n].area();
if (area < 0 && area > -primary_extruder_skirt_brim_line_width * primary_extruder_skirt_brim_line_width * 100)
{
outer_skirt_brim_line.remove(n--);
}
}
skirt_brim_primary_extruder.add(outer_skirt_brim_line);
int length = skirt_brim_primary_extruder.polygonLength();
if (skirt_brim_number + 1 >= primary_line_count && length > 0 && length < primary_extruder_minimal_length) //Make brim or skirt have more lines when total length is too small.
{
primary_line_count++;
}
}
return offset_distance;
}
int SkirtBrim::generatePrimarySkirtBrimLines(int start_distance, unsigned int primary_line_count, const int primary_extruder_skirt_brim_line_width, const int64_t primary_extruder_minimal_length, const Polygons& first_layer_outline, Polygons& skirt_brim_primary_extruder)
{
int offset_distance = start_distance - primary_extruder_skirt_brim_line_width / 2;
for (unsigned int skirt_brim_number = 0; skirt_brim_number < primary_line_count; skirt_brim_number++)
{
offset_distance += primary_extruder_skirt_brim_line_width;
Polygons outer_skirt_brim_line = first_layer_outline.offset(offset_distance, ClipperLib::jtRound);
//Remove small inner skirt and brim holes. Holes have a negative area, remove anything smaller then 100x extrusion "area"
for (unsigned int n = 0; n < outer_skirt_brim_line.size(); n++)
{
double area = outer_skirt_brim_line[n].area();
if (area < 0 && area > -primary_extruder_skirt_brim_line_width * primary_extruder_skirt_brim_line_width * 100)
{
outer_skirt_brim_line.remove(n--);
}
}
skirt_brim_primary_extruder.add(outer_skirt_brim_line);
int length = skirt_brim_primary_extruder.polygonLength();
if (skirt_brim_number + 1 >= primary_line_count && length > 0 && length < primary_extruder_minimal_length) //Make brim or skirt have more lines when total length is too small.
{
primary_line_count++;
}
}
return offset_distance;
}
