void setupRadio() {
printf_begin();
// Setup and configure radio
radio.begin();
radio.setAutoAck(1); // Ensure autoACK is enabled
radio.enableAckPayload(); // Allow optional ack payloads
radio.setRetries(2,15); // Smallest time between retries, max no. of retries
radio.setPayloadSize(8);
radio.setDataRate(RF24_250KBPS);
if( radio.getDataRate() == RF24_250KBPS )
{
debugPrint("Radio is available");
radio_hw_available = true;
radio.startListening(); // Start listening
radio.powerUp();
radio.openWritingPipe(pipes[0]); // Open different pipes when writing. Write on pipe 0, address 0
radio.openReadingPipe(1,pipes[1]); // Read on pipe 1, as address 1
} else {
debugPrint("Radio is NOT available");
}
//radio.printDetails(); // Dump the configuration of the rf unit for debugging
}
void mapFreeCH()
{
radio.setAutoAck(false);
radio.startListening();
radio.stopListening();
for( int i = 30; i< 127; i++)
{
radio.setChannel(i);
radio.startListening();
delay(25);
radio.stopListening();
if ( !radio.testCarrier() )
{
freeCH[nFreeCH++] = i;
}
}
radio.setAutoAck(true);
radio.startListening();
//test printing
for (int i =0; i<nFreeCH; i++)
{
//Serial.println(freeCH[i]);
}
//Serial.println("");
//Serial.print(freeCH[nextFreeCH]);
//Serial.println("");
}
void setup(void)
{
//
// Refer to RF24.h or nRF24L01 DS for settings
radio.begin();
radio.enableDynamicPayloads();
radio.setAutoAck(1);
radio.setRetries(15,15);
radio.setDataRate(RF24_250KBPS);
radio.setPALevel(RF24_PA_MAX);
radio.setChannel(70);
radio.setCRCLength(RF24_CRC_8);
// Open 6 pipes for readings ( 5 plus pipe0, also can be used for reading )
radio.openWritingPipe(pipes[0]);
radio.openReadingPipe(1,pipes[1]);
radio.openReadingPipe(2,pipes[2]);
radio.openReadingPipe(3,pipes[3]);
radio.openReadingPipe(4,pipes[4]);
radio.openReadingPipe(5,pipes[5]);
// Start Listening
radio.startListening();
radio.printDetails();
usleep(1000);
}
void setup(void)
{
wiringPiSetupGpio();
//
// Refer to RF24.h or nRF24L01 DS for settings
radio.begin(WPI_MODE_GPIO);
radio.enableDynamicPayloads();
radio.setAutoAck(1);
radio.setRetries(15,15);
radio.setDataRate(RF24_1MBPS);
radio.setPALevel(RF24_PA_MAX);
radio.setChannel(76);
radio.setCRCLength(RF24_CRC_16);
// Open 6 pipes for readings ( 5 plus pipe0, also can be used for reading )
radio.openWritingPipe(pipes[0]);
radio.openReadingPipe(1,pipes[1]);
radio.openReadingPipe(2,pipes[2]);
radio.openReadingPipe(3,pipes[3]);
radio.openReadingPipe(4,pipes[4]);
radio.openReadingPipe(5,pipes[5]);
//
// Dump the configuration of the rf unit for debugging
//
// Start Listening
radio.startListening();
radio.printDetails();
printf("\n\rOutput below : \n\r");
usleep(1000);
}
// Setup //
void setup(void) {
//
// Print preamble
//
printf("\n\rRF24/examples/scanner/\n\r");
//
// Setup and configure rf radio
//
radio.begin();
radio.setAutoAck(false);
// Get into standby mode
radio.startListening();
radio.stopListening();
// Print out header, high then low digit
int i = 0;
while ( i < num_channels )
{
printf("%x",i>>4);
++i;
}
printf("\n\r");
i = 0;
while ( i < num_channels )
{
printf("%x",i&0xf);
++i;
}
printf("\n\r");
}
void setup(void)
{
// setup interrupt
gpio_export(int_gpio_num);
gpio_set_edge(GPIO_STR, "rising", "1");
radio.begin();
// enable dynamic payloads
radio.enableAckPayload();
radio.enableDynamicPayloads();
radio.setAutoAck(1);
// optionally, increase the delay between retries & # of retries
radio.setRetries(15, 15);
radio.setDataRate(RF24_2MBPS);
radio.setPALevel(RF24_PA_MIN);
radio.setChannel(50);
radio.setCRCLength(RF24_CRC_16);
// Open pipes to other nodes for communication
// Open pipe for reading
radio.openReadingPipe(0, pipes[0]);
radio.openReadingPipe(1, pipes[1]);
// Start listening
radio.startListening();
// Dump the configuration of the rf unit for debugging
radio.printDetails();
}
void setup(void){
//Prepare the radio module
printf("\nPreparing NRF24L01 interface\n");
radio.begin();
radio.setRetries( 15, 15);
radio.setChannel(120);
radio.enableAckPayload();
//radio.disableCRC();
radio.setAutoAck(true);
radio.openWritingPipe(pipes[0]);
radio.openReadingPipe(2,pipes[1]);
radio.openReadingPipe(3,pipes[2]);
radio.openReadingPipe(1,pipes[0]);
radio.printDetails();
printf("\nPreparing MySQL interface.\n");
mysql_connect();
if ((mysql1 != NULL)) {
sprintf(SQLstring,"CREATE TABLE IF NOT EXISTS CC_SENSOR_DYN (timestamp DATETIME, id INTEGER, temperature FLOAT, value INTEGER);");
if (!mysql_query(mysql1, SQLstring)) { printf("SQL CC_SENSOR_DYN Table is Ok: %s\n",SQLstring); } else { printf("SQL CC_SENSOR_DYN NOk: %s\n",SQLstring); printf("%s\n", mysql_error(mysql1)); }
sprintf(SQLstring,"CREATE TABLE IF NOT EXISTS CC_SENSOR_HIST (timestamp DATETIME, id INTEGER, hist_type VARCHAR(1), hist_period INTEGER, value FLOAT);");
if (!mysql_query(mysql1, SQLstring)) { printf("SQL CC_SENSOR_HIST Table is Ok: %s\n",SQLstring); } else { printf("SQL CC_SENSOR_HIST NOk: %s\n",SQLstring); printf("%s\n", mysql_error(mysql1)); }
}
radio.startListening();
printf("\nNow Listening...\n");
}
void sendPacket(Packet packet)
{
radio.stopListening();
radio.openWritingPipe(base_pipe+packet.nodeId); //open pipe unique to the node
radio.setAutoAck(0, false);
radio.write( &packet, sizeof(Packet) );
radio.startListening();
}
void pcmRF::begin(){
radi.begin();
radi.setChannel(1); // Set RF channel to 1
radi.setAutoAck(0); // Disable ACKnowledgement packets
radi.setDataRate(RF24_1MBPS); // Set data rate as specified in user options
radi.setCRCLength(RF24_CRC_8);
radi.openWritingPipe(addresses[1]);
radi.openReadingPipe(1,addresses[0]);
}
void setup(void)
{
// init radio for reading
radio.begin();
radio.enableDynamicPayloads();
radio.setAutoAck(1);
radio.setRetries(15,15);
radio.setDataRate(RF24_1MBPS);
radio.setPALevel(RF24_PA_MAX);
radio.setChannel(76);
radio.setCRCLength(RF24_CRC_16);
radio.openReadingPipe(1,0xF0F0F0F0E1LL);
radio.startListening();
}
void setup(void) {
// init radio for reading
radio.begin();
radio.enableDynamicPayloads();
radio.setAutoAck(1);
radio.setRetries(15,15);
//radio.setDataRate(RF24_1MBPS);
//radio.setPALevel(RF24_PA_MAX);
//radio.setChannel(76);
//radio.setCRCLength(RF24_CRC_16);
radio.openReadingPipe(1,pipes[1]);
radio.startListening();
radio.printDetails();
cout << "Listening...\n";
}
void setup(void)
{
//
// Print preamble
//
//Serial.begin(57600);
//printf_begin();
printf("\n\rRF24/examples/scanner/\n\r");
//
// Setup and configure rf radio
//
radio.begin();
radio.setAutoAck(false);
// radio.enableDynamicPayloads();
radio.setPayloadSize(2);
radio.setDataRate(RF24_250KBPS);
radio.setPALevel(RF24_PA_MAX);
// radio.setChannel(76);
radio.setCRCLength(RF24_CRC_16);
// Get into standby mode
radio.startListening();
radio.stopListening();
radio.printDetails();
// Print out header, high then low digit
int i = 0;
while ( i < num_channels )
{
printf("%x",i>>4);
++i;
}
printf("\n\r");
i = 0;
while ( i < num_channels )
{
printf("%x",i&0xf);
++i;
}
printf("\n\r");
}
void setup(void){
//Prepare the radio module
printf("\nPreparing interface\n");
radio.begin();
radio.enableDynamicPayloads();
radio.setAutoAck(1);
radio.setRetries( 15, 15);
radio.setDataRate(RF24_1MBPS);
radio.setPALevel(RF24_PA_MAX);
radio.setChannel(76);
radio.setCRCLength(RF24_CRC_16);
radio.openWritingPipe(pipes[0]);
radio.openReadingPipe(1,pipes[1]);
radio.startListening();
radio.printDetails();
}
void setup(){
uextPowerOn();
pinMode(LED, OUTPUT);
pinMode(OUT, OUTPUT);
Serial.begin(115200);
printf_begin();
radio.begin();
radio.setCRCLength(RF24_CRC_16);
radio.setDataRate(RF24_1MBPS);
radio.setAutoAck(0);
radio.setRetries(0,0);
radio.setPayloadSize(3);
radio.powerUp();
radio.printDetails();
setupReceive();
}
void RF24Setup( void (*processPacket)(Packet) )
{
radio.begin();
radio.setPayloadSize(sizeof(Packet));
//radio.setChannel(4);
//radio.setDataRate(RF24_250KBPS);
//radio.setRetries(0,15);
radio.openReadingPipe(1,base_pipe);
radio.setAutoAck(1, false);
radio.startListening();
//TODO prety print based on --verbose argument
// printf("\n\rRF24SensorHub!\n");
radio.printDetails();
printf("size of packet = %hu\n", sizeof(Packet));
_processPacket = processPacket;
}
void setup(void)
{
time_t now = time(0);
char* dt = ctime(&now);
cout << "The local time is: " << dt << endl;
tm * gmtm = gmtime(&now);
dt = asctime(gmtm);;
cout << "The UTC date and time is: " << dt << endl;
//
// Refer to RF24.h or nRF24L01 DS for settings
radio.begin();
radio.enableDynamicPayloads();
radio.setAutoAck(1);
radio.setRetries(15,15);
radio.setDataRate(RF24_1MBPS);
radio.setPALevel(RF24_PA_MAX);
radio.setChannel(76);
radio.setCRCLength(RF24_CRC_16);
// Open 6 pipes for readings ( 5 plus pipe0, also can be used for reading )
radio.openWritingPipe(pipes[0]);
radio.openReadingPipe(1,pipes[1]);
radio.openReadingPipe(2,pipes[2]);
radio.openReadingPipe(3,pipes[3]);
radio.openReadingPipe(4,pipes[4]);
radio.openReadingPipe(5,pipes[5]);
//
// Dump the configuration of the rf unit for debugging
//
// Start Listening
radio.startListening();
radio.printDetails();
printf("\n\rOutput below : \n\r");
usleep(1000);
}
void setup(void)
{
radio.begin();
// enable dynamic payloads
radio.enableDynamicPayloads();
// optionally, increase the delay between retries & # of retries
radio.setRetries(15, 15);
radio.setDataRate(RF24_2MBPS);
radio.setPALevel(RF24_PA_HIGH);
radio.setChannel(50);
// Open pipes to other nodes for communication
// Open 'our' pipe for writing
// Open the 'other' pipe for reading, in position #1 (we can have up to 5 pipes open for reading)
radio.openWritingPipe(pipes[0]);
radio.openReadingPipe(1, pipes[1]);
radio.setCRCLength(RF24_CRC_16);
radio.setAutoAck( true ) ;
// Start listening
radio.startListening();
// Dump the configuration of the rf unit for debugging
radio.printDetails();
}
void setup(void)
{
radio.begin();
radio.setPayloadSize(PAYLOAD_SIZE);
radio.setAutoAck(1);
radio.setRetries(15,15);
radio.setDataRate(RF24_1MBPS);
radio.setPALevel(RF24_PA_MAX);
radio.setChannel(10);
radio.setCRCLength(RF24_CRC_16);
//open the pipe
radio.openReadingPipe(1,0xF0F0F0F0E1LL);
// Start Listening
radio.startListening();
//print output
radio.printDetails();
printf("\n\rOutput below : \n\r");
usleep(1000);
}
int main(int argc, char** argv)
{
int fr = atoi(argv[1]);
int to = atoi(argv[2]);
int ac = atoi(argv[3]);
printf("vendor/TMRh20/RF24_RPi/Task\n");
// Refer to RF24.h or nRF24L01 DS for settings
radio.begin();
delay(5);
radio.setPayloadSize(10);
radio.setRetries(15,15); // optionally, increase the delay between retries & # of retries
//radio.setAutoAck(1); // Ensure autoACK is enabled
radio.setAutoAck(0); // Ensure autoACK is disabled
radio.setPALevel(RF24_PA_HIGH);
radio.setDataRate(RF24_250KBPS);
//radio.setCRCLength(RF24_CRC_8);
radio.setChannel(114);
radio.openWritingPipe(pipes[(to-1)]); // atoi() change a char to a int
radio.openReadingPipe(1,pipes[(fr-1)]);
radio.startListening();
radio.printDetails();
// First, stop listening so we can talk.
radio.stopListening();
radio.powerUp();
// Take the time, and send it. This will block until complete
char payload_send[10] = "";
snprintf(payload_send, 10, "to:%d,ac:%d", to, ac);
char payload_send_size[10] = "";
snprintf(payload_send_size, 10, "%d", sizeof(payload_send));
printf("Sending ..\n");
printf("Payload size: ");
printf(payload_send_size);
printf("\n");
printf("Payload: ");
printf(payload_send);
printf("\n");
//bool ok = radio.write( &payload_send, 10 );
radio.write( &payload_send, 10 );
/*if (!ok){
printf("failed.\n");
exit(1);
}*/
//radio.powerDown();
// Now, continue listening
radio.startListening();
// Wait here until we get a response, or timeout (250ms)
unsigned long started_waiting_at = millis();
bool timeout = false;
// Reading temperature or humidity takes about 250 milliseconds!
// Sensor readings may also be up to 2 seconds 'old' (its a very slow sensor)
while ( ! radio.available() && ! timeout ) {
if (millis() - started_waiting_at > 3000 ) {
timeout = true;
}
}
// Describe the results
if ( timeout ) {
printf("err: response timed out.\n");
exit(1);
} else {
// Grab the response, compare, and send to debugging spew
char payload_receive[10] = "";
radio.read( &payload_receive, 10 );
char payload_receive_size[10] = "";
snprintf(payload_receive_size, 32, "%d", 10);
// Spew it
printf("Received ..\n");
printf("Payload size: ");
printf(payload_receive_size);
printf("\n");
printf("Payload: ");
printf(payload_receive);
printf("\n");
printf(payload_receive);
exit(0);
}
exit(1);
}
void setup(void)
{
//
// Role
//
// set up the role pin
// pinMode(role_pin, INPUT);
//digitalWrite(role_pin,HIGH);
// delay(20); // Just to get a solid reading on the role pin
// read the address pin, establish our role
//if ( ! digitalRead(role_pin) )
// role = role_ping_out;
//else
role = role_pong_back;
//
// Print preamble:
//
//Serial.begin(115200);
//printf_begin();
printf("\n\rRF24/examples/pingpair/\n\r");
printf("ROLE: %s\n\r",role_friendly_name[role]);
//
// Setup and configure rf radio
//
radio.begin();
radio.enableDynamicPayloads();
radio.setAutoAck(1);
radio.setRetries(15,15);
radio.setDataRate(RF24_250KBPS);
radio.setPALevel(RF24_PA_MAX);
radio.setChannel(125);
radio.setCRCLength(RF24_CRC_16);
//
// Open pipes to other nodes for communication
//
// This simple sketch opens two pipes for these two nodes to communicate
// back and forth.
// Open 'our' pipe for writing
// Open the 'other' pipe for reading, in position #1 (we can have up to 5 pipes open for reading)
radio.openWritingPipe(pipes[0]);
radio.openReadingPipe(1,pipes[1]);
//
// Start listening
//
radio.startListening();
//
// Dump the configuration of the rf unit for debugging
//
cout << "Mark" << endl;
radio.printDetails();
//lamp[1] = 0;
//lamp[2] = 0;
//cout << "Lamp 1: " << lamp[1] << endl;
//cout << "Lamp 2: " << lamp[2] << endl;
}
