void setup() {
// - Setup serial port
Serial.begin(115200);
// - Pin initialization
pinMode(STEP_UP_PIN, OUTPUT);
digitalWrite(STEP_UP_PIN, LOW);
// - Read address selection
pinMode(ADDRESS_SELECTION_PIN, INPUT_PULLUP);
if(digitalRead(ADDRESS_SELECTION_PIN) == HIGH) {
nodeAddress[0] = 0x01;
} else {
nodeAddress[0] = 0x02;
}
// - Setup and configure radio
radio.begin();
//radio.enableDynamicPayloads();
radio.setPayloadSize(PAYLOAD_SIZE);
radio.setDataRate(RF24_250KBPS); // - Lower speed
radio.setPALevel(RF24_PA_HIGH); // - Higher power level
radio.openWritingPipe(gatewayAddress); // - To send values
radio.openReadingPipe(1, nodeAddress); // - Not used in reality
radio.powerDown();
}
void setup(void)
{
printf("\n\rnRF24l01+ remotecmd\n\r");
//
// Setup and configure rf radio
//
radio.begin();
// optionally, increase the delay between retries & # of retries
radio.setRetries(15,15);
// optionally, reduce the payload size. seems to
// improve reliability
// radio.setPayloadSize(PACKET_LENGTH);
radio.setChannel(0x4c);
radio.setPALevel(RF24_PA_MAX);
//
// Open pipes to other nodes for communication
//
// Open pipe for writing
// Open the 'other' pipe for reading, in position #1 (we can have up to 5 pipes open for reading)
radio.openWritingPipe(pipes[0]);
radio.openReadingPipe(1,pipes[1]);
}
void setup(void)
{
wiringPiSetupGpio();
//
// Refer to RF24.h or nRF24L01 DS for settings
radio.begin(WPI_MODE_GPIO);
radio.enableDynamicPayloads();
radio.setAutoAck(1);
radio.setRetries(15,15);
radio.setDataRate(RF24_1MBPS);
radio.setPALevel(RF24_PA_MAX);
radio.setChannel(76);
radio.setCRCLength(RF24_CRC_16);
// Open 6 pipes for readings ( 5 plus pipe0, also can be used for reading )
radio.openWritingPipe(pipes[0]);
radio.openReadingPipe(1,pipes[1]);
radio.openReadingPipe(2,pipes[2]);
radio.openReadingPipe(3,pipes[3]);
radio.openReadingPipe(4,pipes[4]);
radio.openReadingPipe(5,pipes[5]);
//
// Dump the configuration of the rf unit for debugging
//
// Start Listening
radio.startListening();
radio.printDetails();
printf("\n\rOutput below : \n\r");
usleep(1000);
}
void setup(void) {
//maxa = EEPROM.read(CONFIG_START);
//EEPROM.write(CONFIG_START, maxa);
lcd.begin (20,4);
delay(10);
lcd.setBacklightPin(BACKLIGHT,POSITIVE);
lcd.setBacklight(HIGH);
lcd.clear();
delay(10);
lcd.home ();
Serial.begin(57600);
printf_begin();
radio.begin();
radio.setPALevel(RF24_PA_MAX); //RF24_PA_MIN = 0, RF24_PA_LOW, RF24_PA_HIGH, RF24_PA_MAX, RF24_PA_ERROR
radio.setDataRate(RF24_250KBPS); //RF24_1MBPS = 0, RF24_2MBPS, RF24_250KBPS
//radio.setAutoAck(1);
radio.setRetries(15,15);
radio.enableDynamicPayloads();
radio.openWritingPipe(pipes[1]);
radio.openReadingPipe(1, pipes[0]);
radio.startListening();
radio.printDetails();
}
/********************************************************************************
Main
********************************************************************************/
int main(void) {
// initialize code
usart_init();
// enable interrupts
//sei();
_delay_ms(2000);
printf("Start NRF24L01P test...");
radio.begin();
radio.setRetries(15,15);
radio.setPayloadSize(8);
radio.setPALevel(RF24_PA_MAX);
radio.setChannel(120);
radio.openWritingPipe(pipes[1]);
radio.openReadingPipe(1,pipes[0]);
radio.startListening();
radio.printDetails();
loop();
// main loop
while (true) {
_delay_ms(1000);
printf("Elapsed: %u \n", TCNT1);
}
}
void setup(void)
{
// setup interrupt
gpio_export(int_gpio_num);
gpio_set_edge(GPIO_STR, "rising", "1");
radio.begin();
// enable dynamic payloads
radio.enableAckPayload();
radio.enableDynamicPayloads();
radio.setAutoAck(1);
// optionally, increase the delay between retries & # of retries
radio.setRetries(15, 15);
radio.setDataRate(RF24_2MBPS);
radio.setPALevel(RF24_PA_MIN);
radio.setChannel(50);
radio.setCRCLength(RF24_CRC_16);
// Open pipes to other nodes for communication
// Open pipe for reading
radio.openReadingPipe(0, pipes[0]);
radio.openReadingPipe(1, pipes[1]);
// Start listening
radio.startListening();
// Dump the configuration of the rf unit for debugging
radio.printDetails();
}
void setup(void)
{
//
// Refer to RF24.h or nRF24L01 DS for settings
radio.begin();
radio.enableDynamicPayloads();
radio.setAutoAck(1);
radio.setRetries(15,15);
radio.setDataRate(RF24_250KBPS);
radio.setPALevel(RF24_PA_MAX);
radio.setChannel(70);
radio.setCRCLength(RF24_CRC_8);
// Open 6 pipes for readings ( 5 plus pipe0, also can be used for reading )
radio.openWritingPipe(pipes[0]);
radio.openReadingPipe(1,pipes[1]);
radio.openReadingPipe(2,pipes[2]);
radio.openReadingPipe(3,pipes[3]);
radio.openReadingPipe(4,pipes[4]);
radio.openReadingPipe(5,pipes[5]);
// Start Listening
radio.startListening();
radio.printDetails();
usleep(1000);
}
void setup(void){
radio.begin();
radio.setPALevel(RF_24_PA_MAX);
radio.setChannel(0x75);
radio.openWritingPipe(0xF0F0F0F0E1LL);
radio.enableDynamicPayloads();
radio.powerUp();
}
/********************************************************************************
Main
********************************************************************************/
int main(void) {
// initialize usart module
usart_init();
// enable interrupts
sei();
// Init GPIO
initGPIO();
// Init Timer 1
initTimer();
// Init Timer 0 & 2
initTimers();
OCR0A = 255;
OCR0B = 255;
OCR2A = 255;
OCR2B = 255;
_delay_ms(1000);
OCR0A = 0;
OCR0B = 0;
OCR2A = 0;
OCR2B = 0;
fixZeroValueOCR();
// Console friendly output
printf("Start...");
printf(CONSOLE_PREFIX);
// Init NRF24L01+
radio.begin();
radio.setRetries(15,15);
radio.setPayloadSize(8);
radio.setPALevel(RF24_PA_MAX);
radio.setChannel(115);
radio.openWritingPipe(pipes[0]);
radio.openReadingPipe(1,pipes[1]);
radio.startListening();
// Some RF module diagnostics logs
radio.printDetails();
// main loop
while (1) {
// main usart loop for console
usart_check_loop();
}
}
void radioSetup() {
radio.begin();
radio.setRetries(15, 15);
radio.setChannel(0x4c); //76
radio.setPALevel(RF24_PA_MAX);
radio.setPALevel(RF24_PA_MAX);
radio.openWritingPipe(pipes[0]);
radio.openReadingPipe(1, pipes[1]);
radio.startListening();
radio.printDetails();
printf("Radio setup is complete!\n");
}
//Initial setup of GPIO Pins and pipe modes (read/write).
void setup(void)
{
radio.begin();
radio.setRetries(15,15);
radio.setChannel(0x4c);
radio.setPALevel(RF24_PA_MAX);
radio.openWritingPipe(pipes[0]);
radio.openReadingPipe(1,pipes[1]);
radio.openReadingPipe(2,pipes[2]);
radio.openReadingPipe(3,pipes[3]);
radio.startListening();
radio.printDetails();
}
void setup(void)
{
// init radio for reading
radio.begin();
radio.enableDynamicPayloads();
radio.setAutoAck(1);
radio.setRetries(15,15);
radio.setDataRate(RF24_1MBPS);
radio.setPALevel(RF24_PA_MAX);
radio.setChannel(76);
radio.setCRCLength(RF24_CRC_16);
radio.openReadingPipe(1,0xF0F0F0F0E1LL);
radio.startListening();
}
void setup(void){
//Prepare the radio module
printf("\nPreparing interface\n");
radio.begin();
radio.setRetries( 15, 15);
radio.setChannel(0x4c);
radio.setPALevel(RF24_PA_MAX);
radio.setPALevel(RF24_PA_MAX);
radio.openWritingPipe(pipes[0]);
radio.openReadingPipe(1,pipes[1]);
radio.startListening();
radio.printDetails();
}
void setupRF24(){
radio.begin();
// Set the PA Level low to prevent power supply related issues since this is a
// getting_started sketch, and the likelihood of close proximity of the devices. RF24_PA_MAX is default.
// radio.setPALevel(RF24_PA_LOW);
radio.setPALevel(RF24_PA_MAX);
// Open a writing and reading pipe
radio.openWritingPipe((byte *) TXNAME);
radio.openReadingPipe(1, (byte *) RXNAME);
// Start the radio listening for data
radio.startListening();
radio.powerDown();
}
void setup(void)
{
//
// Print preamble
//
//Serial.begin(57600);
//printf_begin();
printf("\n\rRF24/examples/scanner/\n\r");
//
// Setup and configure rf radio
//
radio.begin();
radio.setAutoAck(false);
// radio.enableDynamicPayloads();
radio.setPayloadSize(2);
radio.setDataRate(RF24_250KBPS);
radio.setPALevel(RF24_PA_MAX);
// radio.setChannel(76);
radio.setCRCLength(RF24_CRC_16);
// Get into standby mode
radio.startListening();
radio.stopListening();
radio.printDetails();
// Print out header, high then low digit
int i = 0;
while ( i < num_channels )
{
printf("%x",i>>4);
++i;
}
printf("\n\r");
i = 0;
while ( i < num_channels )
{
printf("%x",i&0xf);
++i;
}
printf("\n\r");
}
void setup(void){
//Prepare the radio module
printf("\nPreparing interface\n");
radio.begin();
radio.enableDynamicPayloads();
radio.setAutoAck(1);
radio.setRetries( 15, 15);
radio.setDataRate(RF24_1MBPS);
radio.setPALevel(RF24_PA_MAX);
radio.setChannel(76);
radio.setCRCLength(RF24_CRC_16);
radio.openWritingPipe(pipes[0]);
radio.openReadingPipe(1,pipes[1]);
radio.startListening();
radio.printDetails();
}
void setup(void)
{
time_t now = time(0);
char* dt = ctime(&now);
cout << "The local time is: " << dt << endl;
tm * gmtm = gmtime(&now);
dt = asctime(gmtm);;
cout << "The UTC date and time is: " << dt << endl;
//
// Refer to RF24.h or nRF24L01 DS for settings
radio.begin();
radio.enableDynamicPayloads();
radio.setAutoAck(1);
radio.setRetries(15,15);
radio.setDataRate(RF24_1MBPS);
radio.setPALevel(RF24_PA_MAX);
radio.setChannel(76);
radio.setCRCLength(RF24_CRC_16);
// Open 6 pipes for readings ( 5 plus pipe0, also can be used for reading )
radio.openWritingPipe(pipes[0]);
radio.openReadingPipe(1,pipes[1]);
radio.openReadingPipe(2,pipes[2]);
radio.openReadingPipe(3,pipes[3]);
radio.openReadingPipe(4,pipes[4]);
radio.openReadingPipe(5,pipes[5]);
//
// Dump the configuration of the rf unit for debugging
//
// Start Listening
radio.startListening();
radio.printDetails();
printf("\n\rOutput below : \n\r");
usleep(1000);
}
void setup(void)
{
radio.begin();
radio.setPayloadSize(PAYLOAD_SIZE);
radio.setAutoAck(1);
radio.setRetries(15,15);
radio.setDataRate(RF24_1MBPS);
radio.setPALevel(RF24_PA_MAX);
radio.setChannel(10);
radio.setCRCLength(RF24_CRC_16);
//open the pipe
radio.openReadingPipe(1,0xF0F0F0F0E1LL);
// Start Listening
radio.startListening();
//print output
radio.printDetails();
printf("\n\rOutput below : \n\r");
usleep(1000);
}
void setup(void)
{
radio.begin();
// enable dynamic payloads
radio.enableDynamicPayloads();
// optionally, increase the delay between retries & # of retries
radio.setRetries(15, 15);
radio.setDataRate(RF24_2MBPS);
radio.setPALevel(RF24_PA_HIGH);
radio.setChannel(50);
// Open pipes to other nodes for communication
// Open 'our' pipe for writing
// Open the 'other' pipe for reading, in position #1 (we can have up to 5 pipes open for reading)
radio.openWritingPipe(pipes[0]);
radio.openReadingPipe(1, pipes[1]);
radio.setCRCLength(RF24_CRC_16);
radio.setAutoAck( true ) ;
// Start listening
radio.startListening();
// Dump the configuration of the rf unit for debugging
radio.printDetails();
}
void setup(void)
{
//
// Setup and configure rf radio
//
radio.begin();
// optionally, increase the delay between retries & # of retries
radio.setRetries(20, 20);
radio.setPayloadSize(PAYLOAD);
// TODO: set other crap (data rate, spi rate, etc)
radio.setDataRate(RF24_2MBPS);
radio.setChannel(0x4c);
radio.setPALevel(RF24_PA_MAX);
//
// Open pipes to other nodes for communication
//
// TODO: configure this to match correctly on the Arduino
radio.openWritingPipe(pipes[0]);
radio.openReadingPipe(1, pipes[1]);
//
// Start listening
//
radio.startListening();
//
// Dump the configuration of the rf unit for debugging
//
//radio.printDetails();
std::cerr << "OK Listening for commands" << std::endl;
}
int main(int argc, char** argv)
{
int fr = atoi(argv[1]);
int to = atoi(argv[2]);
int ac = atoi(argv[3]);
printf("vendor/TMRh20/RF24_RPi/Task\n");
// Refer to RF24.h or nRF24L01 DS for settings
radio.begin();
delay(5);
radio.setPayloadSize(10);
radio.setRetries(15,15); // optionally, increase the delay between retries & # of retries
//radio.setAutoAck(1); // Ensure autoACK is enabled
radio.setAutoAck(0); // Ensure autoACK is disabled
radio.setPALevel(RF24_PA_HIGH);
radio.setDataRate(RF24_250KBPS);
//radio.setCRCLength(RF24_CRC_8);
radio.setChannel(114);
radio.openWritingPipe(pipes[(to-1)]); // atoi() change a char to a int
radio.openReadingPipe(1,pipes[(fr-1)]);
radio.startListening();
radio.printDetails();
// First, stop listening so we can talk.
radio.stopListening();
radio.powerUp();
// Take the time, and send it. This will block until complete
char payload_send[10] = "";
snprintf(payload_send, 10, "to:%d,ac:%d", to, ac);
char payload_send_size[10] = "";
snprintf(payload_send_size, 10, "%d", sizeof(payload_send));
printf("Sending ..\n");
printf("Payload size: ");
printf(payload_send_size);
printf("\n");
printf("Payload: ");
printf(payload_send);
printf("\n");
//bool ok = radio.write( &payload_send, 10 );
radio.write( &payload_send, 10 );
/*if (!ok){
printf("failed.\n");
exit(1);
}*/
//radio.powerDown();
// Now, continue listening
radio.startListening();
// Wait here until we get a response, or timeout (250ms)
unsigned long started_waiting_at = millis();
bool timeout = false;
// Reading temperature or humidity takes about 250 milliseconds!
// Sensor readings may also be up to 2 seconds 'old' (its a very slow sensor)
while ( ! radio.available() && ! timeout ) {
if (millis() - started_waiting_at > 3000 ) {
timeout = true;
}
}
// Describe the results
if ( timeout ) {
printf("err: response timed out.\n");
exit(1);
} else {
// Grab the response, compare, and send to debugging spew
char payload_receive[10] = "";
radio.read( &payload_receive, 10 );
char payload_receive_size[10] = "";
snprintf(payload_receive_size, 32, "%d", 10);
// Spew it
printf("Received ..\n");
printf("Payload size: ");
printf(payload_receive_size);
printf("\n");
printf("Payload: ");
printf(payload_receive);
printf("\n");
printf(payload_receive);
exit(0);
}
exit(1);
}
void setup(void)
{
//
// Role
//
// set up the role pin
// pinMode(role_pin, INPUT);
//digitalWrite(role_pin,HIGH);
// delay(20); // Just to get a solid reading on the role pin
// read the address pin, establish our role
//if ( ! digitalRead(role_pin) )
// role = role_ping_out;
//else
role = role_pong_back;
//
// Print preamble:
//
//Serial.begin(115200);
//printf_begin();
printf("\n\rRF24/examples/pingpair/\n\r");
printf("ROLE: %s\n\r",role_friendly_name[role]);
//
// Setup and configure rf radio
//
radio.begin();
radio.enableDynamicPayloads();
radio.setAutoAck(1);
radio.setRetries(15,15);
radio.setDataRate(RF24_250KBPS);
radio.setPALevel(RF24_PA_MAX);
radio.setChannel(125);
radio.setCRCLength(RF24_CRC_16);
//
// Open pipes to other nodes for communication
//
// This simple sketch opens two pipes for these two nodes to communicate
// back and forth.
// Open 'our' pipe for writing
// Open the 'other' pipe for reading, in position #1 (we can have up to 5 pipes open for reading)
radio.openWritingPipe(pipes[0]);
radio.openReadingPipe(1,pipes[1]);
//
// Start listening
//
radio.startListening();
//
// Dump the configuration of the rf unit for debugging
//
cout << "Mark" << endl;
radio.printDetails();
//lamp[1] = 0;
//lamp[2] = 0;
//cout << "Lamp 1: " << lamp[1] << endl;
//cout << "Lamp 2: " << lamp[2] << endl;
}
