void setup(void)
{
// setup interrupt
gpio_export(int_gpio_num);
gpio_set_edge(GPIO_STR, "rising", "1");
radio.begin();
// enable dynamic payloads
radio.enableAckPayload();
radio.enableDynamicPayloads();
radio.setAutoAck(1);
// optionally, increase the delay between retries & # of retries
radio.setRetries(15, 15);
radio.setDataRate(RF24_2MBPS);
radio.setPALevel(RF24_PA_MIN);
radio.setChannel(50);
radio.setCRCLength(RF24_CRC_16);
// Open pipes to other nodes for communication
// Open pipe for reading
radio.openReadingPipe(0, pipes[0]);
radio.openReadingPipe(1, pipes[1]);
// Start listening
radio.startListening();
// Dump the configuration of the rf unit for debugging
radio.printDetails();
}
void setup(void)
{
//
// Refer to RF24.h or nRF24L01 DS for settings
radio.begin();
radio.enableDynamicPayloads();
radio.setAutoAck(1);
radio.setRetries(15,15);
radio.setDataRate(RF24_250KBPS);
radio.setPALevel(RF24_PA_MAX);
radio.setChannel(70);
radio.setCRCLength(RF24_CRC_8);
// Open 6 pipes for readings ( 5 plus pipe0, also can be used for reading )
radio.openWritingPipe(pipes[0]);
radio.openReadingPipe(1,pipes[1]);
radio.openReadingPipe(2,pipes[2]);
radio.openReadingPipe(3,pipes[3]);
radio.openReadingPipe(4,pipes[4]);
radio.openReadingPipe(5,pipes[5]);
// Start Listening
radio.startListening();
radio.printDetails();
usleep(1000);
}
void setup(void)
{
wiringPiSetupGpio();
//
// Refer to RF24.h or nRF24L01 DS for settings
radio.begin(WPI_MODE_GPIO);
radio.enableDynamicPayloads();
radio.setAutoAck(1);
radio.setRetries(15,15);
radio.setDataRate(RF24_1MBPS);
radio.setPALevel(RF24_PA_MAX);
radio.setChannel(76);
radio.setCRCLength(RF24_CRC_16);
// Open 6 pipes for readings ( 5 plus pipe0, also can be used for reading )
radio.openWritingPipe(pipes[0]);
radio.openReadingPipe(1,pipes[1]);
radio.openReadingPipe(2,pipes[2]);
radio.openReadingPipe(3,pipes[3]);
radio.openReadingPipe(4,pipes[4]);
radio.openReadingPipe(5,pipes[5]);
//
// Dump the configuration of the rf unit for debugging
//
// Start Listening
radio.startListening();
radio.printDetails();
printf("\n\rOutput below : \n\r");
usleep(1000);
}
void pcmRF::begin(){
radi.begin();
radi.setChannel(1); // Set RF channel to 1
radi.setAutoAck(0); // Disable ACKnowledgement packets
radi.setDataRate(RF24_1MBPS); // Set data rate as specified in user options
radi.setCRCLength(RF24_CRC_8);
radi.openWritingPipe(addresses[1]);
radi.openReadingPipe(1,addresses[0]);
}
void setup(void)
{
// init radio for reading
radio.begin();
radio.enableDynamicPayloads();
radio.setAutoAck(1);
radio.setRetries(15,15);
radio.setDataRate(RF24_1MBPS);
radio.setPALevel(RF24_PA_MAX);
radio.setChannel(76);
radio.setCRCLength(RF24_CRC_16);
radio.openReadingPipe(1,0xF0F0F0F0E1LL);
radio.startListening();
}
void setup(void)
{
//
// Print preamble
//
//Serial.begin(57600);
//printf_begin();
printf("\n\rRF24/examples/scanner/\n\r");
//
// Setup and configure rf radio
//
radio.begin();
radio.setAutoAck(false);
// radio.enableDynamicPayloads();
radio.setPayloadSize(2);
radio.setDataRate(RF24_250KBPS);
radio.setPALevel(RF24_PA_MAX);
// radio.setChannel(76);
radio.setCRCLength(RF24_CRC_16);
// Get into standby mode
radio.startListening();
radio.stopListening();
radio.printDetails();
// Print out header, high then low digit
int i = 0;
while ( i < num_channels )
{
printf("%x",i>>4);
++i;
}
printf("\n\r");
i = 0;
while ( i < num_channels )
{
printf("%x",i&0xf);
++i;
}
printf("\n\r");
}
void setup(){
uextPowerOn();
pinMode(LED, OUTPUT);
pinMode(OUT, OUTPUT);
Serial.begin(115200);
printf_begin();
radio.begin();
radio.setCRCLength(RF24_CRC_16);
radio.setDataRate(RF24_1MBPS);
radio.setAutoAck(0);
radio.setRetries(0,0);
radio.setPayloadSize(3);
radio.powerUp();
radio.printDetails();
setupReceive();
}
void setup(void){
//Prepare the radio module
printf("\nPreparing interface\n");
radio.begin();
radio.enableDynamicPayloads();
radio.setAutoAck(1);
radio.setRetries( 15, 15);
radio.setDataRate(RF24_1MBPS);
radio.setPALevel(RF24_PA_MAX);
radio.setChannel(76);
radio.setCRCLength(RF24_CRC_16);
radio.openWritingPipe(pipes[0]);
radio.openReadingPipe(1,pipes[1]);
radio.startListening();
radio.printDetails();
}
void setup(void)
{
time_t now = time(0);
char* dt = ctime(&now);
cout << "The local time is: " << dt << endl;
tm * gmtm = gmtime(&now);
dt = asctime(gmtm);;
cout << "The UTC date and time is: " << dt << endl;
//
// Refer to RF24.h or nRF24L01 DS for settings
radio.begin();
radio.enableDynamicPayloads();
radio.setAutoAck(1);
radio.setRetries(15,15);
radio.setDataRate(RF24_1MBPS);
radio.setPALevel(RF24_PA_MAX);
radio.setChannel(76);
radio.setCRCLength(RF24_CRC_16);
// Open 6 pipes for readings ( 5 plus pipe0, also can be used for reading )
radio.openWritingPipe(pipes[0]);
radio.openReadingPipe(1,pipes[1]);
radio.openReadingPipe(2,pipes[2]);
radio.openReadingPipe(3,pipes[3]);
radio.openReadingPipe(4,pipes[4]);
radio.openReadingPipe(5,pipes[5]);
//
// Dump the configuration of the rf unit for debugging
//
// Start Listening
radio.startListening();
radio.printDetails();
printf("\n\rOutput below : \n\r");
usleep(1000);
}
void setup(void)
{
radio.begin();
radio.setPayloadSize(PAYLOAD_SIZE);
radio.setAutoAck(1);
radio.setRetries(15,15);
radio.setDataRate(RF24_1MBPS);
radio.setPALevel(RF24_PA_MAX);
radio.setChannel(10);
radio.setCRCLength(RF24_CRC_16);
//open the pipe
radio.openReadingPipe(1,0xF0F0F0F0E1LL);
// Start Listening
radio.startListening();
//print output
radio.printDetails();
printf("\n\rOutput below : \n\r");
usleep(1000);
}
void setup(void)
{
radio.begin();
// enable dynamic payloads
radio.enableDynamicPayloads();
// optionally, increase the delay between retries & # of retries
radio.setRetries(15, 15);
radio.setDataRate(RF24_2MBPS);
radio.setPALevel(RF24_PA_HIGH);
radio.setChannel(50);
// Open pipes to other nodes for communication
// Open 'our' pipe for writing
// Open the 'other' pipe for reading, in position #1 (we can have up to 5 pipes open for reading)
radio.openWritingPipe(pipes[0]);
radio.openReadingPipe(1, pipes[1]);
radio.setCRCLength(RF24_CRC_16);
radio.setAutoAck( true ) ;
// Start listening
radio.startListening();
// Dump the configuration of the rf unit for debugging
radio.printDetails();
}
void setup(void)
{
//
// Role
//
// set up the role pin
// pinMode(role_pin, INPUT);
//digitalWrite(role_pin,HIGH);
// delay(20); // Just to get a solid reading on the role pin
// read the address pin, establish our role
//if ( ! digitalRead(role_pin) )
// role = role_ping_out;
//else
role = role_pong_back;
//
// Print preamble:
//
//Serial.begin(115200);
//printf_begin();
printf("\n\rRF24/examples/pingpair/\n\r");
printf("ROLE: %s\n\r",role_friendly_name[role]);
//
// Setup and configure rf radio
//
radio.begin();
radio.enableDynamicPayloads();
radio.setAutoAck(1);
radio.setRetries(15,15);
radio.setDataRate(RF24_250KBPS);
radio.setPALevel(RF24_PA_MAX);
radio.setChannel(125);
radio.setCRCLength(RF24_CRC_16);
//
// Open pipes to other nodes for communication
//
// This simple sketch opens two pipes for these two nodes to communicate
// back and forth.
// Open 'our' pipe for writing
// Open the 'other' pipe for reading, in position #1 (we can have up to 5 pipes open for reading)
radio.openWritingPipe(pipes[0]);
radio.openReadingPipe(1,pipes[1]);
//
// Start listening
//
radio.startListening();
//
// Dump the configuration of the rf unit for debugging
//
cout << "Mark" << endl;
radio.printDetails();
//lamp[1] = 0;
//lamp[2] = 0;
//cout << "Lamp 1: " << lamp[1] << endl;
//cout << "Lamp 2: " << lamp[2] << endl;
}
